Question about 1997 Honda CBR 600 F(3)V

1 Answer

How do I adjust the rear tire on a 97 honda cbr 600f3

Simply that, How do I adjust the rear tire on my 97 honda cbr f3? I want to take some slack out of my chain. Is this the procedure I must take to do so? Also, How much slack should a motorcycle chain have to it?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

40mm slack up and down middle of chain. not tight when sitting on bike. loosen axle ajust both sides evenly, retighten axle install new split pin

Posted on Dec 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 98 cbr 600f3 the turn signals work so times or just one will work. What could cause that?


If you park outside or live in a humid or salty area like I do, then I've found it can really help to split the switch gear open (be careful not to let anything fall out), clean every contact surface you can find and then spray everything with WD40 or Tri-Flow to displace any moisture and inhibit corrosion. I've owned a lot of Hondas over the years and had almost every switch stop working at one point or another and this almost always stops the problem. Plus an f3 is just abou the right age for this to start happening. If it doesn't work then you probably have a short (which would be odd for a Honda unless its been crashed or modified.

May 01, 2012 | 1998 Honda CBR 600 F(3)W

1 Answer

How do you adjust rear shock up on a 1989 honda cbr 600


Standard settings are...Rear Preload: Position 3
Rear Compression: 1 turn out from maximum (punch aligned)
Rear Rebound: 1 turn out from maximum (punch aligned)
This is for the 97 & 98 year models.

Jul 26, 2011 | 1989 Honda CBR 600 F Hurricane

1 Answer

What are the stock tire sizes on a 1998 honda cbr f3?


it depends on the dealer ???whats recomended is in the owners manual

Jul 06, 2010 | 1998 Honda CBR 600 F(3)W

1 Answer

I have 97 cbr 600 f3 and apparently we took my gas tank off to repair my idle adjust screw does wnyone know where the gas lines hook back up?


Easiest way to find out is fill some petrol into tank and see where it drip out from. Good enough help?

Apr 23, 2010 | 1997 Honda CBR 600 F(3)V

2 Answers

How do you fix a broken odometer and speedomter in a '97 cbr600 f3?


It sounds like the cable to the the speedo and the tach may need to be replaced. check them and replace if needed.

Mar 24, 2010 | 1997 Honda CBR 600 F(3)V

2 Answers

96 CBR 600F3 runs for approx 10Min then stalls out.


Check the vacuum pipe from the carbs to the fuel tap, if its gat a pin hole in as you demand more fuel the vacuum loss cuts downthe fuel flow and the bike will stop!

Jul 28, 2009 | 1997 Honda CBR 600 F(3)V

2 Answers

Where is the fuel filter located on 1997 honda cbr 600


I have a 1996 CBR 600F3. Mine is directly under the gas tank. Where the gas tank meets the seat. If you remove the single top bolt for the gas tank and the lower bolt for the gas tank you can lift the tank a little. Then you will see the rubber gas fuel line. The filter will be in-line.

Jun 18, 2009 | 1997 Honda CBR 600 F(3)V

1 Answer

Bigger tire size for a 1997 honda 600 f3


Stock is a 160/60ZR17. I run a 170/60ZR17 with no issues. That is as wide as you can go on the rear without major modification to the swingarm or rubbing the stock arm.

Mar 10, 2009 | 1997 Honda CBR 600 F(3)V

1 Answer

97 honda cbr 600f3 shifting, gears, etc.


It should be 1 down and 5 up. About the 5500rpm at 85... That sounds about right with stock gearing. Let me know if i can help further. Good luck and happy holidays. Jay

Dec 04, 2008 | 1997 Honda CBR 600 F(3)V

Not finding what you are looking for?
1997 Honda CBR 600 F(3)V Logo

Related Topics:

370 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

yadayada
yadayada

Level 3 Expert

63801 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...