Question about 2004 Yamaha TT-R 125 L

6 Answers

Yamaha TTR 125 L won't idle

2004 Yamaha TTR 125 L will start and idle (low) with the choke on. If I turn off the choke, i have to keep the engine revved to keep the bike going. There is no hesitation on acceleration. The bike sat for six months. I soaked the carb and changed the gas in the tank. What is the problem? Or what do I need to do next?

Posted by on

  • 3 more comments 
  • Anonymous Jan 20, 2009

    I have

  • Anonymous Mar 04, 2009

    Yep mine is doing that too. Say's on the frame to adjust the throttle set screw, that's not on the carb but on the throttle cable?

  • Anonymous Apr 13, 2009

    Wife Dropped her 125 and it started being hard to find idle.. now it wont start at all... It acts like its not gettting fuel.. Cab teare down next

  • Anonymous Mar 23, 2014

    Why will the ttr 50 idle with the choke on but won't idle when you turn the choke off

  • Doug Dec 03, 2016

    Then take a screw driver or ratchet, give the carb a few solix taps on the side of the float bowl. If the carb still leaks fuel out remove it. Take off the float bowl, omove the float retainer pin, float, and plunger. When doing this keep a close eye ont for debris or damage that would cause the float to stick open. Inspect the plunger to be sure the rubber tip is not cracked or damaged, it must be in good working order to shut off fuel flow. Clear any debris from the carb and jets since you are that far into it anyway it wont hurt doing so. Re-install the float components and check that the float is adjusted correctly. Google the correct float level specs. for your bike to be accurate. Then put it back together, axjust your pilot air screw to factory spec. Start the bike anx check for proper operation. Once it warms to normal operating temperature adjust the Idle to your preference. Good luck

×

Ad

6 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I cleaned the carb on the bike and put it back together and now it is as if the float is stuck open and is just dumping gas out of the carb all over the ground.

Posted on Sep 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

This is very tipical. when bikes are stored the fuel varishes up the jets & needles. soak the carb. moving it back and forth in the soak solution. then blow every jet and orfice with a controlled air source. note: any speck of rust or dirt can plug these jets. pay attention to detail and do every thing twice. then install the carb and adjust it to your riding style. later Spike

Posted on Mar 25, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

The problem is that your idle is adjusted to low just like mine, you need to adjust your idle

Posted on Aug 04, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I got a 2008 ttr 125 from this guy and he said it sat for 6 months. it wouldn't start at first so i bought a new spark plug and tried to start it, wouldn't start, drained the gas put new in. wouldn't start, then i took the carbueator off and clean it out wouldn't start, so i took it off one more time and clean it really good with carb cleaner and clean out all the holes with a wire and then put it all back together then it finally started but now it starts with the choke on and idle with the choke on but soon as i take the choke off it doesnt want to idle i got to keep it going cant let up all the way on the throttle or else it just shuts off. I going to mess with the idle screw turn it up see if that works, but does anybody have any suggestion? oh and i also bought a new battery for it for the electric starter and that all works. just wont idle?

Posted on May 09, 2012

  • donnalmmon
    donnalmmon May 09, 2012

    i got a 2008 ttr 125 from this guy and he said it sat for 6 months. it wouldn't start at first so i bought a new spark plug and tried to start it, wouldn't start, drained the gas put new in. wouldn't start, then i took the carbueator off and clean it out wouldn't start, so i took it off one more time and clean it really good with carb cleaner and clean out all the holes with a wire and then put it all back together then it finally started but now it starts with the choke on and idle with the choke on but soon as i take the choke off it doesnt want to idle i got to keep it going cant let up all the way on the throttle or else it just shuts off. I going to mess with the idle screw turn it up see if that works, but does anybody have any suggestion? oh and i also bought a new battery for it for the electric starter and that all works. just wont idle?

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove pilot jet out of carberator. Clean and re-install

Posted on Mar 14, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 55 Answers

Did you adjust the idle.or tamper with the air screw when you cleaned the car? also did you take the jets out and blow them out with a air nossle? try that if you haven't already.

Posted on Nov 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Yamaha ttr 90 for my son. I cleaned the jets. Then itwould not idle so I adjusted the Idle on the handle bars. Now it hesitates when I twist the throttle. And before I adjusted the throttle...


Hi, Anonymous and the usual suspects are:
1. Idle speed improperly adjusted.
2. Air fuel mixture screws not properly adjusted.
3. Inlet system air leak.
4. Leaking accelerator pump.
5. Loose low-speed jet.
6. Plugged low-speed jet.
7. Contaminated or plugged low-speed circuit.
8. Enrichner valve/choke not seated or leaking.
9. Multi carburetors out of sync and need to be balanced.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2002 ttr90 won idle
TTR90 Carb Fix
YAMAHA TTR90 Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-tt-owners-manuals

Oct 29, 2013 | 2005 Yamaha TTR 90 E

1 Answer

Yamaha 125 ttr idles to slow


Hi, Anonymous the carburetor throttle shaft wheel has two cables the cable closest to the right side of the bike is the throttle cable and the one closest to the left side is the idle cable. Right about the middle between the two is the idle adjustment bolt it faces out towards the air filter end of the carb. The engine should be at operating temperature with the enrichener off to set the idle between 950-1050 rpm. Turn the idle adjustment bolt clockwise to increases idle speed and counterclockwise to decrease idle speed. If you have access to your air fuel mixture bolt you may adjust it as well if not there is a video below on how to gain access, make sure you start with clean or new spark plugs. Gently turn the air fuel mixture bolt clockwise until it starts to bottom out "STOP" do not over tighten as it will damage the taper on the end, now back it out 2 full turns to establish a starting point start the engine and check the idle rpm's and adjust the idle adjustment bolt accordingly for 950-1050 rpm if necessary, adjust the air fuel mixture bolt 1/4 turn at a time and let the engine settle for about 10 seconds, clockwise for a leaner mixture and counterclockwise for a richer mixture you are seeking the highest rpm your air fuel mixture bolt can acquire without going past 3 full turns from bottom then readjusting the idle adjustment bolt back down to 950-1050 rpm If you can not detect any rpm change and can not stall the engine by turning the air-fuel mixture bolt all the way in then your pilot/low-speed jet is too big. Final adjustment should be made with a clean air filter mounted to the carburetor. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have wonderful a day.
Other Yamaha TTR 125 4T carb help
how to set idle up on ttr125 Texas Offroad Network Forums
YAMAHA TT R125 Owner Service Manual
OEM parts for Yamaha
YAMAHA TT R110E Owner Manual

Jul 20, 2012 | 2006 Yamaha TTR 125 E

1 Answer

My 2005 yamaha ttr 125 won't start, I change the spark plug and the conpression seem ok. What else could be?


Hi, N_glutek and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. A severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
13. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
14. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
15. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
16. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
17. Faulty neutral, clutch lever, or kickstand safety switch.
18. Faulty fuel pump or fuse or relay.
19. A stuck bent or burnt valve.
20. Tilt sensor needs a reset.
21. Security system not disarming alarm needs a reset.
22. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
TTR 125 won start need help
Yamaha TTR 125 Won Start eHow
YAMAHA TT R125 Owner Service Manual
OEM parts for Yamaha
YAMAHA TT R110E Owner Manual

Apr 04, 2012 | 2003 Yamaha TT-R 125

1 Answer

04 ttr 225 carb appears to be gummed up. Full throttle is OK but need choke on full to idle and run at slow speeds


Hi, Shall582 and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on the blue links below. Good luck and have a wonderful day.
TTR125 won idle except with the choke on
2001 TTR225 wont run unless choke is on
http://tjsconcepts.com/ttr225/TTR225_Service_Manual.pdf
OEM parts for Yamaha
Yamaha TT R250 Owner Manual

Jun 29, 2011 | 2004 Yamaha TT-R 225

1 Answer

2002 yamaha ttr 225 idles high when let off gas but eventually idles down on its own and hard to start when cold with choke or without


Hi, David and the usual suspects are:
1. Throttle cables improperly adjusted, pinched or need lubrication.
2. Idle adjusting screw needs to be backed off.
4. Air fuel mixture adjusted too lean start with 2 full turns.
5. Intake system air leak.
6. Fast idle choke ramp is not releasing.
7. Broken throttle return spring.
8. Damaged diaphragm or slide.
9. Faulty MAP, TPS, ATS, O2, sensors or wiring/connector
10. Multi carburetors not in sync.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links blue below. Good luck and have a wonderful day.
TTR 225 Carb Problems
TTR 125 Idle Issues
http://tjsconcepts.com/ttr225/TTR225_Service_Manual.pdf
OEM parts for Yamaha
http://tjsconcepts.com/ttr225/TTR225_Owner_Manual.pdf

Jun 21, 2011 | 2002 Yamaha TT-R 225

1 Answer

Cant get a yamaha ttr 125 to start


I'm having a hard time keeping the engine to idle without the choke to stay on position. When the choke is off, engine would shut off.
any clue?

Mar 20, 2010 | 2004 Yamaha TT-R 125 L

2 Answers

Yamaha ttr 90 jet pilot should it be open end to


The pilot should be open. This is to say that if you look through it at a light you should be able to see through it.
I suggest blowing it out with compressed air as well as the hole it fits in. While your at it give all the jets a blow out.
once you've put it back together I also suggest you fit an in-line fuel filter.
This will help to keep the dirt out and save you having ths same problem again
Hope this helps
Regards Andrew Porrelli

Dec 08, 2009 | 2004 Yamaha TT-R 125 E

1 Answer

I have a Yamaha TTR 225 4 stroke that is having issues starting


Carba/f ratio needs adjusting and use of the choke will help keep the idle circuits clean.

Nov 12, 2009 | 2003 Yamaha YZ 250

1 Answer

2005 Yamaha TT-R 125 LE will not idle without choke on


Hi, Kirkbb1 and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on the blue links below. Good luck and have a wonderful day.
TTR125 won idle except with the choke on
2004 TTR125 been sitting won idle
YAMAHA TT R125 Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-tt-owners-manuals

Apr 06, 2009 | 2005 Yamaha TT-R 125 LE

Not finding what you are looking for?
2004 Yamaha TT-R 125 L Logo

5,731 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...