Question about 2008 Suzuki GSX 1300 R Hayabusa

1 Answer

Can anyone tell me the torque setting for stator rotor/crank bolt

05/2008 hayabusa

Posted by on

  • Anonymous Mar 18, 2014

    Changed ecm and stator but still no fire



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Sorry, could not wait, got the info elsewhere.

Posted on Nov 23, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Aprilia sx 50 torque setting

Hi Anonymous I am sorry you can't find the first and best tool you ever bought for your Aprilia but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
DOWNLOAD 2011 Aprilia Sx 50

Btw, I’m available to help over the phone in case u need at

Jan 15, 2012 | 2011 Aprilia SX 50

1 Answer

How do i replace the regulator & stator on a 92

There's nothing to replacing the regulator. It simply bolts to the frame. The wires from the regulator to the stator plug into the plug on the lower left front of the engine case. The larger longer wires runs back along the frame and up to the positive post of the battery.

There's a bit more to replacing the stator. To replace the stator, disconnect the battery and drain the primary case. Remove the outer primary cover. You'll have to take the engine compensator sprocket nut off and remove the mainshaft nut that holds the clutch assembly on. To get the clutch assembly off, remove the snap ring in the center of the clutch assembly and remove the clutch adjuster. The mainshaft nut is inside the hole in the center of the clutch assembly. The nut has LEFT HANDED THREADS. Take the nut off the primary chain adjuster and take the engine sprocket, primary chain with adjuster, and the clutch assembly off all together. The rotor is on the engine sprocket shaft. It can be difficult to get off because of the magnets inside of it. The rotor has two holes in it. I use two long bolts and put them just into the holes deep enough to hold the rotor by squeezing the ends together. Pull the rotor off. The stator is held on by four small Torx bolts and it has a wire support that is held on by two small sheet metal screws. When you install the new stator, make sure you use thread locker on the threads and torque the bolts to 40 inch pounds of torque. The sprocket shaft nut torques to 150-165 foot pounds of torque. The clutch mainshaft nut (LEFT HANDED THREADS) torques to 60-80 foot pounds. You'll probably need a locking bar or some way to prevent the engine from turning while you torque the nuts.

Good Luck

Aug 01, 2011 | Harley Davidson FXR Super Glide...

1 Answer

How do ichange my altanator

To change the stator in your alternator, you must first disconnect the battery. Then drain the primary and remove the cover. Take the compensator nut off the sprocket shaft and remove the nut on the primary chain adjuster. Then, remove the circlip that holds the clutch adjuster into the center of the clutch assembly. Remove the mainshaft nut that holds the clutch assembly on. This nut has left-handed threads. Grab the compensator sprocket and the clutch assembly and remove these and the primary chain all at the same time. Behind the sprocket shaft extension is a shim or several shims, remove these and remember where the go. You'll see the rotor. It has two holes in it. Use some long bolts that will go into the holes. Insert the bolts and squeeze them together. Pull the rotor off. It may be difficult to get off as it has very strong magnets in it but it will come off. Behind the rotor is the stator. Remove the four Torx bolts and the two small screws that hold the plug into the case. Remove the stator. Replace the stator and all the rest of the assembly is the reverse of the disassembly. The mainshaft nut (left-handed threads) torques to 60-80 foot pounds. The compensator sprocket nut torques to 150-165 foot pounds. You'll need a locking bar to prevent the engine from turning while applying torque to these nuts. Adjust the primary chain to have 3/4 to 7/8 inch up and down play with the engine cold. Replace the primary cover and add oil. If you are going to attempt to do this job, I'd strongly suggest you purchase a service manual.

Good Luck

May 24, 2011 | 2003 Harley Davidson FXST Softail Standard

1 Answer

How to install stator

To install a stator on your Softail, you'll have to remove the outer primary, the engine drive sprocket, primary chain, and clutch assembly. Then, you can get to the four screws that holds the stator. The job is not that difficult if you've got a few tools and a bit of mechanical skills. The engine sprocket is quite tight and you'll probably need an air wrench or a "locking bar" to keep the engine from turning while you torque the engine nut holding the sprocket. The engine sprocket torques to 150-165 foot pounds and the clutch nut torques to 60-80 foot pounds LEFT HANDED. Some click type torque wrenches will not work in the left handed direction. The clutch nut is behind the adjuster plate in the center of the clutch assembly. Just take the snap ring out and you'll see it.

I use two 5/16" bolts about three inches long to remove the magnetic rotor. Stick the bolts just slightly in the two holes and squeeze them together so that they bind. Then pull the rotor off. Take the four torqs, out of the stator and the two screws out of the plastic plug retainer. Work the plug out of the case and lift the stator off the sprocket shaft. Install the new stator by coating the new plug with black RTV. Put the stator over the sprocket shaft and then work the plug into the hole in the engine case. Put the stator in place and put the NEW bolts that came with it in place and start them. Put the plastic plug retainer in and then torque the stator bolts to 40 inch pounds.

Mar 11, 2011 | 2005 Harley Davidson FXST - FXSTI Softail...

1 Answer

How to remove generator from engine (model DGUH5S-2). 11 horsepower Honda engine.GX340 .

I have not worked on Dunlite generators, however have worked on many different brands using the GX340. When removing generator parts, one must keep in mind the brushes contacting the armature. Remove brush pack if any and set to side. Next unplug stator wiring making sure to draw diagram of connections. Remove bolts mounting generator/stator housing to frame and carefuflly pull off leaving only armature /rotor on the crank of the engine. Remove the long bolt thru rotor into crank. Now you will need to apply penetrating oil to the shaft of the engine to loosen the rust on the taper. It may take several applications. Place a piece of hardwood against
metal to protect the rotor and firmly rap with hammer on
both sides. You may need to use pry bar against engine
and rotor as you hammer hardwood. Repeat as necessary,
some rotors will be very stuck due to rust. Be very
carefull with hammer and or prybars not to damage
windings. Have patience and let oil work. Good luck.

Jan 28, 2011 | Electrical Supplies

1 Answer

Looking for step by step instructions on replacing a stator on a 2001 FXDWG

To replace the stator on your Wide Glide, you'll have to pull the outer primary cover off. This means drain the oil and remove the outer primary cover. Then, you'll need a wrench to remove the large nut on the engine compensator sprocket. You'll probably need a "locking bar" to wedge between the sprokets to lock the assembly from turning. Remove the snap ring in the center of the clutch assembly, remove the clutch release plate that is held in by the snap ring. Inside the clutch is a nut that has LEFT HANDED THREADS, remove this nut. Take the nut off the primary chain adjuster. Grab the clutch assembly and the engine compensator sprocket and lift these parts and the chain off as a unit.

Now, there are some thin spacers that go behind the sprocket shaft extension and a 0.090" thick spacer that goes behind the rotor. Do not mix these shims up. You'll see two holes in the rotor. I use two 5/16" bolts about three inches long to get the rotor off. Stick them in the holes just slightly, squeeze the outer ends towards each other and pull the rotor off. The magnets are pretty strong. The stator is held on by four small Torx head bolts and there's nylon retainer with two small screws that hold the plug in. Retorque the four Torx head screws to 40 inch pounds of torque with a Loctite #242 blue or equivalent thread locking compound on them. Reassembly is the reverse of the assembly. The torque on the clutch assembly nut (mainshaft nut) is 60-70 foot pounds with one line of Loctite #271 red locktite, (remember this nut has left-handed threads) and the engine compensator sprocket torques to 150-165 foot pounds with two lines of Loctite #271 red. Adjust the primary chain so that the up and down play in the center of the top run is 3/4" to 7/8" cold. Outer primary bolts torque to 100 inch pounds.

For a better explanation, you'll need an OEM service manual.

Good Luck

Oct 24, 2010 | 2001 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

Have a 1982 suzuki motorcycle gs1100gk starter turns magneto but is not cranking engine is this a keyway problem

Actually no this happened because the bolt holding the magneto on was not properly tighten to the correct torque a loose rotor will shear the key remove the rotor and inspect the key way remove what left and install a new set key and properly torque the bolt.

Apr 05, 2010 | 1983 Suzuki GSX 1100 E

1 Answer

How many pounds of torque do ineed on the crank case of a gsx1300r suzuki

Do not fool around with this and learn how to properly torque bolts. Get a proper manual - all torque values are in it. If you strip the threads (remember they are fine threads and do not need very much tightning and are in Aluminum - a soft material.


Mar 03, 2010 | 2003 Suzuki GSX 1300 RZ Hayabusa

1 Answer

Torque settings for renault megane engine

Does anyone know the torque settings for the following Cam box(bolts), head bolts & crank shaft, the megane scenic is 2001.

May 01, 2009 | Renault Sportwagon Cars & Trucks

Not finding what you are looking for?
2008 Suzuki GSX 1300 R Hayabusa Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

81400 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides