Question about 1973 kawasaki Z1

1 Answer

Z900/gpz gearbox converion

What model gpz gearbox slots into the 73/76 model z9oo

Posted by on

  • alkiracing Dec 19, 2008

    thanks heaps,will let you how it goes

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

The GPZ 1100 80-83 model gearbox will fit just fine.

Posted on Dec 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I purchased a Kawasaki GPZ 1100 1995 model there was no ignition switch completely unattached from the wire harness what wires would i connect to hotwire


Phillip, the GPZ is essentially a KZ 1100. If the color codes are correct, then if you put the red and the yellow wires together, this should give you power. However, as a temporary fix only, I will give you some good replacement options that should help you out. ^^ Good luck, and hope this helps.
KAWASAKI GPZ 1100 1995 1998 ALL MODELS IGNITION SWITCH

Dec 03, 2015 | kawasaki Motorcycles

1 Answer

Gas converion


Since no model number was given, gas dryer conversion kits usually come with instructions. The usually require you to replace the burner orifice, and make an adjustment to the regulator already included with the dryer. In some cases speacial tools are required to perform the conversion. Pleazer Appliance...

Apr 08, 2014 | Samsung 7.3 Cu. Ft. 7-Cycle Gas Dryer -...

1 Answer

Gearbox has lots of play


Hello, If you are asking about the steering box, then there is usually a slotted bolt with a jam nut on it. You adjust the tension by placing a screwdriver on the slotted bolt to keep it in place, then back off the jam nut. Once free, the slotted bolt is turned clockwise until snug. Then hold this position and turn the jamnut to hold the setting. Some people jack the weight off the front tires to make this adjustment and some leave the weight on the wheels.

When the gears have too much wear in the teeth inside the steering box, you will not be able to get satisfaction by adjusting the bearing. The gearbox is shot and needs replacing. You did not say what Model or Year of product you are fixing. If you have rack and pinion you can get looseness in the valving and again in the Tie-rod links.

The other type of gearbox would be the transmission. If you were asking about the trans looseness it would only be in the shift mechanism. They do wear out.

I hope my suggestion has been very helpful.

Aug 11, 2011 | Ford F-150 Cars & Trucks

1 Answer

Starts to turn over then load clunk and stops rock bike in gear and it will free motor and start


Sounds like there is a tooth or several from the gears floating about somewhere in the engine/gearbox.
A strip down job I would say.

Feb 02, 2011 | 1987 kawasaki GPz 1000 RX

1 Answer

Gpz600r gearbox works in reverse


the shifter can be reversed ( 180 )remove it and replace the other way round

Jan 15, 2010 | 1989 kawasaki GPZ 500 S - GPX 500 R

1 Answer

I have a Sharp ViewcamZ VL-Z900. DEW error


Dew has condensed in the camera. Eject the cassette but leave the cassette door open.remove the battery . Borrow a hair drier . set it to optimum temperature(not vey hot but but hot enough to cause discomfort when blown on fingers). direct the hot air through the cassette compartment door for about five minutes. reattach the battery and reinsert the tape.
Good Luck,
Luwangula

Sep 18, 2009 | Cameras

1 Answer

I need proper torque specs for clutch relese springs 84 gpz 1100


You are over torquing the springs. Buy a generic manual from your automotive shop. ZX11 specs are much higher than the GPZ.

Aug 20, 2009 | 1995 kawasaki GPZ 1100

2 Answers

Kawasaki 87 stickers


RdDecals.com in Canada has complete sets or individual sticker pairs including pinstripes for the US Ninja version, but not the GPZ. So, with one of these kits, you could get all of the right stickers except the GPZ (comes with Ninja) stickers on the upper cowl, and the 1000RX for the belly pan (comes with 1000R). They have stickers for other older Kawasaki's as well.

May 26, 2009 | 1987 kawasaki GPz 1000 RX

2 Answers

I need igniter of kawasaki gpz 400r type


Google " motorcycle salvage Kawasaki " You can probably fine it there.

May 07, 2009 | 1987 kawasaki GPZ 500 S - GPX 500 R

1 Answer

Replacing Z900 brake calipers


If your looking to buy brake calipers call (870) 458-2939 They may have them. I hope this helps

Nov 17, 2008 | 1975 kawasaki Z1B

Not finding what you are looking for?
1973 kawasaki Z1 Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

69199 Answers

chris

Level 2 Expert

232 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...