Question about 2004 Kymco Venox 250

1 Answer

Oil level Hi, I can't see the oil level on my bike. The manual says to pour 2 liters after draining the old oil, should I just do that? Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,512 Answers

Hi saturnin

That's the best way to get it right. Do what the manual tells you to do.

To check the oil

  1. Put the bike on level concrete on the center stand
  2. Check the oil with the dipper in the oil fill hole.
  3. Check it hot 10 mins after turning off the bike by unscrewing the oil fill plug, wipe the stick, and just dip it without screwing it back in, and check it for level.
  4. Pour in small amounts at a time to top it right up to the mark, but never ever over fill it.
  5. Screw back in the plug/dipper.
Hope this helps, am happy to answer any other questions you may have about it. Cheers!!

regards
robotek

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How much oil do I put in


put a bit in at a time and check the dip stick untill it is at the full mark

Jan 09, 2015 | Motorcycles

1 Answer

What oil should i use in my dirt bike it's a 2005 kawasaki 125cc 4 stroke,and how much oil shouls i put in it I took all the old out


Hi,
Just use an ordinary 4T motor oil, 15W/40 will be okay. Your oil capacity is 800ml but you could pour the 1 liter, before putting the lubricant clean the oil filter and drain plug.
Hope that helps you out!

Jun 30, 2011 | kawasaki KLX 125 Motorcycles

1 Answer

How many quarts of oil go in a 1980 honda cx500 motor cycle? and where should the oil level be on the dip stick? thanks, sladerivers@aol.com


i would suggest using a good 10w 40 engine oil and simply put the bike on the centre stand pouring in 2 litres to start thats if the bike has been drained empty then just top up little at a time untill oil is in the markers on the dip stick the bike will hold around the 3 litre mark from empty hope this helps

Oct 27, 2010 | 1980 Honda CX 500 A

1 Answer

Hi, i need to know what kind of oil you recommend for a 1995 xt 600 and the oil capacity, thank you


Use only JASO MA certified motorcycle oil. 10w-40 for cooler climates. 20w-50 for warmer conditions. Any oil that says Energy conserving on the label will shorten the life of your wet clutch and transmission gears. Synthetic oil help your bike run cooler and shift easier.You will need 3 quarts of oil and will have some left over. How much you need to put in depends on how well you drain the old oil. There should be two drain points, one on the frame and one on the motor. You will have to pour in between 2 and 2 1/2 quarts and run the motor for 5 minutes before you can accurately check the oil level. Then top up as necessary but do not over fill it .

Oct 06, 2010 | 1995 Yamaha XT 600 E

1 Answer

What type of oil and how much does the 92 VT1100 use?


You will need to get 4 quarts of JASO MA rated motorcycle oil, a filter, and a drain bolt washer. Get 10w-40 for cold climate or 20w-50 for warm climate/long distance riding.Do not use any oil that says Energy Conserving on the label , it will shorten the life of your wet clutch and transmission gears. Synthetic oil will make your bike run cooler and shift easier.Drain the old oil and put the drain bolt back in with a new washer. Change the filter and pour in 3 1/2 quarts of oil. Start the bike and run for a minute. Check the oil level and top up as needed.

Oct 01, 2010 | 1992 Honda VT 1100 C Shadow

1 Answer

Where do you fill the transmission on a 2000 m2 cyclone buell motorcycle


Take cover off where u adjust clutch on primary just follow clutch cable where it enters primary to right 4 bolts get new gasket from harley take off cover below is a drain bolt take out drain old oil put back in get 2 guarts of air,cooled,wet clutch engine oil pour in where u took 4 bolts out of cover stand bike up straight or pour a little then stand bike up to see level where oil is the level should be even with bottom of clutch diaphragm spring the drain plug torque is 14-30 foot pounds of torque remeber bike up straight and the amount of oil for next time use 2 inch hole above shifter with 2 bolts has o-ring do not need to replace ever time drain replace plug torque pour exact amount u poured in primary when u took out the 4 bolts. Use wet clutch oil or u will destroy cluth material inside and u will go no where no exception otherwise have a couple hundred in bank to replace clutch and u can put any kind of oil u want just have other tranportation and not be in A hurry to get anywhere

Apr 29, 2010 | 2001 Buell M2 Cyclone

1 Answer

I want to tknow the steps of changing oil in the V-Strom 650


14mm wrench. 2. An oil filter wrench, if you're changing the filter. Either a 3/8" drive ratchet or a 17mm wrench to turn the oil filter 3. Oil--you need about 3 quarts of 10W/40. I use synthetic motorcycle oil, MOTUL, but any good oil will probably be fine as long as you change it. Oil filter, if it's being changed--Suzuki pn# 16510-34E00. As a minor note, the sv650(s) needs 2.9Q of oil if you also change the filter, rather than merely changing the oil without changing the
filter (2.4Q). 4. Newspaper, something to catch oil in and a rag. Drain the oil from a warm engine by removing the 14 mm nut on the bottom of the engine on the left side, having first spread newspaper under the bike and put your catch pan underneath. Remember that bolts mostly come out counterclockwise (Righty tighty, Lefty loosey). For directionally challenged, you might have to lay on your back to figure this out. Also remove the filler plug on the right side of the engine to help drainage. If you don't know which is the filler plug, check your owner's manual to find out--under oil. If you're changing the filter, remove it using your special tool. To replace the oil, screw in the drain plug. It should be pretty tight, but don't put all your weight on it. Replace the filter by putting some oil on the gasket, and then turning the filter on till you feel the gasket contact the engine. Using the special tool, tighten it two turns more. Pour oil into the filler, 2.4 US qt, 2.0 imp qt, or 2.3 liters. Start the bike and run it a few minutes. Turn it off and holding the bike level, check the oil level in the sight glass on the right side of the engine. If it's above full, drain a bit out, if below low, add a bit more. Pour the oil into a jug and take it to a recycling center or gas station for disposal, don't just pour it out. Throw away the newspapers, go wash your hands, and go for a ride!

Oct 13, 2009 | 2006 Suzuki DL 650 V-Strom

2 Answers

Where do i put the oil back in the bike after i drain the oil? drained the oil and now do not know where to replace this oil please help!


There is a dipstick near the top level of the radiator on the right side of the bike. Just remove the dipstick and pour in the fresh oil.
To check oil level, let the bike idle for three minutes then turn it off. Now use the dipstick to read the oil level.

Please rate this solution. Thanks Eagle!

Apr 17, 2009 | 2002 Yamaha YZ 426 F

2 Answers

Genral oil change


Look for the oil dip stick. Now look under underneath the area of bike where the dip stick is. You'll see a round disc with a bolt. That is the drain plug. Now you found it lets begin.
1. Warm the bike up.
2. Turn bike off.
3. Take oil dip stick out.
4. Have your oil pan under the bike
5.. Unbolt drain plug. A spring and screen will come out keep them together.
6. After oil finished draining. Make sure Screen is clean before replacing back in with the spring.
7. Start the bolt in by hand then finish with tightening with socket.
8. Put oil dip stick back in. you're ready to go!

It takes 15W 40 ( .9 liters) Don't forget to press yes if this was helpful : )

Nov 10, 2008 | 2005 Kymco Grand Dink 250

2 Answers

Genral oil change


1.Get your supplies ready and expose your engine 2.Unscrew the Oil Filler Cap 3.Remove the Oil Drain Plug 4.Remove and Replace the Crush Washer 5.Clean the Oil Drain Plug 6.Remove the Oil Filter 7.Remove and Clean Plastic Mesh Filter 8.Lubricate the O-ring of the New Filter and Attach it to the Engine 9.Motorcycle Oil Change - Replace Oil Drain Plug & Plastic Mesh Filter Pour Oil 10.Check the Oil Level,,

Nov 10, 2008 | 2008 Buell XB12XT

Not finding what you are looking for?
2004 Kymco Venox 250 Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

61129 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4477 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...