Question about 2001 kawasaki ZX-6R Ninja

1 Answer

Power shut down when it reaches 100mph

I have a 04 zx636 ninja i had loss of power when i reach the speed of 100mph. what is the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 599 Answers

ASD? auto shut down ..computer rev limiter set for 100?

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4 3 misfire idle


Hi, Anonymous and the usual suspects are:
1. Idle speed improperly adjusted.
2. Inlet system air leak.
3. Leaking accelerator pump.
4. Loose low-speed jet.
5. Plugged low-speed jet.
6. Contaminated or plugged low-speed circuit.
7. Enrichner valve not seated or leaking.
For more information about your issue please visit the websites below and for specific information or questions you can reach me at xlch@mail.com. Good luck and have nice day.
How to diagnose carburetor vacuum leaks on your motorcycle
BRZ bad idle misfire no CEL stock engine
R6 motorcycle cylinder misfire power loss fault finding spark check.. http://www.lewisportusa.com/manuals.htm
http://www.betamotor.com/en/support/manuals


Jan 07, 2014 | Beta Motorcycles

1 Answer

What is the max rpm to run a vl 800 at


Found this in the Suzuki VZ800K5 Manual.\:

Chapter 9-20
"The fuel cut-off circuit is incorporated in this ECM in order to prevent over-running of engine. When engine
speed reaches 8000 r/min during running, this circuit cuts off fuel at the fuel injector."

Found this in the Suzuki VZ800K4 Manual ... The 04 does NOT have FI but this performs as I said above..

Chapter 8-16
"The fuel cut-off circuit is incorporated in this ignitor in order to prevent over-running of engine. When engine
speed reaches 8000 r/min during running, this circuit cuts off primary circuit for all spark plugs."

May 12, 2011 | 2004 Suzuki VL 800 Volusia

1 Answer

My 03 kawasaki ninja zx636 will not display a speed reading it happened when my chain came off when i was riding the temp gauge works and the revs show but no speed reading


Hi there,

you'll need to check for the speedometer cable (of its analog.) the cable inside it might be broken. Else, i suppose when your chain snapped, it hit the wires connected to the speedometer. might as well check it out.
Hope this helps,

Dec 27, 2010 | 2003 kawasaki ZX-6R

1 Answer

Bike was in an accident, need to replace the ignition switch assembly. Don't know what to do. it's a 2004 kawi ninja zx636


The ignition switch comes as you quite rightly say as a module/assembly. It is connected by one multiplug. Just buy a new switch and plug it in.
Hope that helps.

Dec 11, 2010 | kawasaki ZX-6R Motorcycles

1 Answer

My speedometer cable broke, how can i fix it myself?i have a 2002 250 ninja


Unscrew the connector at the front wheel. If you can reach the connector under the speedometer unscrew it. If you can not reach it you will have to take the parts in your way off. I would suggest a careful examination using a mirror to see if it can be done with very few items removed. A dentists mirror is ideal for this. Otherwise take pictures as you go to aid re-assembly. You may get away with merely removing the upper fairing. Good Luck.

Feb 19, 2010 | 2008 kawasaki Ninja 250R

1 Answer

How do i remove my ninja's front signals?


You have to partially remove the front fairing. Unbolt from the fuel tank and remove the uppermost guards and try to reach inside to access.

Dec 12, 2009 | 2008 kawasaki Ninja 250R

1 Answer

Is my dented front frame repairable?


No way to tell for sure without someone who straightens frames taking a look at it. I've dealt with Ron at framestraightsystems.com, he will give you an honest opinion.

No, parts are not cheap. Anywhere.

Apr 14, 2009 | 2006 kawasaki ZX-6R

Not finding what you are looking for?
2001 kawasaki ZX-6R Ninja Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

Angelo Stewart
Angelo Stewart

Level 2 Expert

224 Answers

yadayada
yadayada

Level 3 Expert

63801 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...