Question about 1998 kawasaki ZL 250 Eliminator

1 Answer

Remove seat How do you remove the seat on eliminator 250?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,336 Answers

On an '89, remove both side covers and you will see a bolt on both sides of the bike just under the seat. Remove the bolts, lift the back of the seat and slide toward the rear of the bike.

Posted on Nov 10, 2008

2 Suggested Answers

  • 2336 Answers

SOURCE: remove seat

On an '89, remove both side covers and you will see a bolt on both sides of the bike just under the seat. Remove the bolts, lift the back of the seat and slide toward the rear of the bike.

Posted on Nov 10, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi good day I am having a time setting the carbs on my El 250 could you tell me the setting on the jet pins ?I have tried 2 turns and then 2.5 turns should I go up or down ?


Turn the throttle screw and the air screw inward until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. This is the factory setting. If you actually tighten them down at all, you will create a "ring" on the adjuster and it may affect performance. Please rate my answer. Thanks!
ffbfdb2.gif

Jul 17, 2010 | 2007 kawasaki EL 250 Eliminator

1 Answer

How do I remove a one peice seat from a 1983 honda cb 250 custom?


this bike seat bolts on one bolt on each side of seat, towards the rear of the seat, then lift tail end of seat and pull backward.

Jun 13, 2010 | 1972 Honda CB 250

1 Answer

Dont start i need find de fuse box


Look under the seat or side panel,the fuses may be sealed in a black box which is clipped shut to protect from the wet.

Mar 04, 2010 | 2001 kawasaki EL 250 Eliminator V

1 Answer

How d'ya remove the sparkplugs on an Eliminator


Sadly you'll benefit from rachet, extension(s), swivel or swivel socket, and a socket.
Just takes alittle geting use to.

Dec 10, 2009 | 2008 kawasaki EL 250 Eliminator

2 Answers

How do you take the seat off a 2006 Eliminator 125 to fit soft luggage?


My 2006 125 Eliminator just got a reupholstered seat. Remove hex bolt at the very rear of seat. Remove right side plastic cover over battery (open with key, pull off cover) .Remove plastic cover on left side (2 large phillips head screws.) Remove 2 stainless hex heads on each side of bike that hold chromed plastic sleeves under passenger part of seat (4 hex heads). Then remove 2 smaller black hex heads (one on each side) under point where tapered passenger part of seat begins. Slide seat toward rear of bike do disengage from metal lip that holds down the front.
Be sure to use metric hex wrenches. 15 minutes or less off or on.

good luck
ride easy

Oct 18, 2009 | 2006 kawasaki EL 125 Eliminator

1 Answer

Kawasaki EL250 carburettor


Turn off the gas and remove the float bowl. Remove the fuel line. Remove the float pin and float with needle valve. Do not bend the tang that the float needle sits on. Spray carb cleaner into the seat where the needle valve came from to clear out any trash in the valve casing. Spray the float bowl and interior of the carb. Remount the needle and float back in place and put the float bowl back on. Install an in-line fuel filter. The diagram below shows a 1994 carb Yours will be the same or close to it.

A “very helpful” rating on this answer? Thanks!

6d12579.gif

Jul 03, 2009 | 2001 kawasaki EL 250 Eliminator V

2 Answers

1994 250cc nighthawk seat removal how to


should have a key that fits the helmet lock at left side below seat. with helmet lock open, pull down on black lever behind helmet lock, then pull seat backwards and up to remove.

Jun 28, 2009 | 1994 Honda CB 250 Nighthawk

1 Answer

After 2 iced winters left outside. Rebel 250 will not start


So you know that you are getting spark but no fuel. Do process of elimination. Start at the pet-****, then check the fuel line to the carb, if fuel is getting to the carb then you need to prove fuel is getting through the carb. Might be debris between the needle and seat or debris inside one of your jets. take your time, good luck.

Apr 27, 2009 | 1999 Honda CMX 250 Rebel

1 Answer

Remove fzr 250 seat


Take off the pillion seat and then release rider seat with the black lever by pushing it across. The rider seat may need a little wiggle to get off.

Mar 21, 2009 | 1988 Yamaha FZR 250

1 Answer

Remove seat


On an '89, remove both side covers and you will see a bolt on both sides of the bike just under the seat. Remove the bolts, lift the back of the seat and slide toward the rear of the bike.

Nov 10, 2008 | 2008 kawasaki EL 250 Eliminator

Not finding what you are looking for?
1998 kawasaki ZL 250 Eliminator Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

Angelo Stewart
Angelo Stewart

Level 2 Expert

224 Answers

yadayada
yadayada

Level 3 Expert

63990 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...