Question about 1993 Suzuki GSF 400 Bandit

1 Answer

Replace the seals

I have to replace the seals on my Suzuki 400 Bandit 1995 model. Does anyone know how much oil each shock takes?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,336 Answers

17.1 ounces per leg.

Posted on Nov 10, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Suzuki GSF 400 Bandit #3 cylinder dead


Hi, Justin, you need "FIVE" things in order for a cylinder to run properly:
1. FUEL: in order to validate your not getting fuel spray some starting fluid into the air cleaner and hit the starter button, if it fires up and runs for a few seconds then you know you have a fuel delivery issue. Multi carb banks should be bench "SYNC"
2. SPARK: remove the spark plug and with it connected to the spark plug cable ground the threads to something metal you should see a bluish white spark if not you have a faulty spark plug, spark plug cable, ignition coil, condenser, CKP, ECM, sensor or the wiring in between.
3. COMPRESSION: you must have at least 80-100 PSI for most bikes, multi-cylinder engines should be within 10-15% of each other if not perform a leak down test you may have a burnt or bent valve or hole in the piston or broken rings.
4. CAM TIMING: confirm your timing marks are aligned to see if the cam chain or adjuster are worn out and the chain has skipped a couple teeth.
5. IGNITION TIMING: on older bikes check to see if your points have not closed up, timing plate has not become loose and confirm with a timing light for proper retard and advance functions, on newer bikes where timing is controlled by an ECM and is nonadjustable check you CKP, TPS, MAP, O2, sensor or its counterpart for integrity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Mysterious problem with my GSF 400
Bandit running on 3 cylinders
Suzuki GSF 400 BANDIT Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
Suzuki GS500 Owner Manual
http://mybikemanuals.com/suzuki

Dec 20, 2017 | 1991 Suzuki GSF 400 Bandit

1 Answer

How are the front forks in my suzuki bandit 600 (1998) made up i.e if i take them apart to replace the springs and oil what will i find inside them ???


That is a good one. You are going to find springs and oil! Unless the seals are leaking, you shouldn't have to touch the forks. If the springs are shot, I would just get a new set of forks. But that is rare. You have to take them apart and spill the oil all over the place and get the seals off and the new ones on. There are books written about your specific forks, just have to dig. They tell you to get a pan like a wallpaper pan, and about 40 newspapers, and pull the tops off and catch the oil, then pull the springs out with all the washers etc, Not a hard job.Need about 2 bottles of fork oil, each one takes about 3/4 of a bottle. It is a premeasured amount, you will have to look that up too. Hope this helps.

May 20, 2010 | Motorcycles

1 Answer

92 suzuki bandit 400 gs-f, ran but it didn't idle after carb clea


hi buddy on my bike i had this problem when you rev it it will rev down gradually so it changed the jets and ir worked so try this buddy then get back to me give me a good rating

Sep 15, 2009 | 1992 Suzuki GSF 400 Bandit

1 Answer

Engine oil went low , clutch difficult to engage


The clutch got cooked, so it does need to be replaced, unfortunately.

Regards,
matt

Sep 15, 2009 | 1991 Suzuki GSF 400 Bandit

2 Answers

Front rim for my 1991 gsf 400 bandit


No. The gs500 has rotor on right side. 600s have two rotors. The following website will let you compare part numbers. http://www.suzukipartshouse.net/pages/parts/viewbybrand/parts.aspx

May 29, 2009 | 1991 Suzuki GSF 400 Bandit

2 Answers

Suzuki Bandit 400 not starting


The starter motor could be the culprit, check the starter motor.

Apr 15, 2009 | 1993 Suzuki GSF 400 Bandit

1 Answer

Gsf 400 bandit clutch needs replacing how do i do it?


Real easy, just drain oil, take off side case and remove the bolts.
Take it off as an assembly.
Make sure clutch plates and friction plates are positioned correctly.

Are you sure you need to replace the clutch?
I assume it merely needs a minor adjustment.

Feb 17, 2009 | 1991 Suzuki GSF 400 Bandit

Not finding what you are looking for?
1993 Suzuki GSF 400 Bandit Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...