Question about 1979 Suzuki GS 750 E

1 Answer

GS CAMS I am looking for a set of cams for my 82 gs 750 ez I understand that my exhaust cam is the same as the one on the 82 1100E.What about the intake? Do you know if I can use one off another model?or if there is another model gs that runs with the same intake cam.I have the 16 valve TSCC motor.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,336 Answers

Unfortunately I can't give you any technical details since my knowlegde of the GS (or any other bike in that matter) is very limited. However there are a copple of ways you can use your internet connexion to find out more: 1. try http://www.gsresources.com (= GS(X) site worthwhile!) 2. try http://www.google.com and search for intake cam suzuki gs 750 (or otherwise)

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i change the cam belt on a 2007 bmw r1200gs adventure motorbike


There is no cam belt. Cams are chain driven and you have to remove and strip the entire motor to change the chains.

Feb 03, 2015 | 2007 BMW R 1200 GS Adventure

1 Answer

What is the factory jet size for a suzuki gs 850gl


i recently just installed air pods on my 82 gs 850. Installed 155 jets, the stock jets were 115.

Mar 24, 2013 | 1978 Suzuki GS 750 E

1 Answer

How do you take off 1981 suzuki timing chain for cam and celender removal


remove airbox, rubbers, throttle, choke, gas tank (disconnect fuel line and vacuum first), valve breather, rpm attachment near the front of the valve cover, exhaust headers, remove valve cover (place somewhere you won't step on it) remove cams(i'm sure theres a right order to take them off but I never really had a problem with taking them off any order) remove bolts on the outside of the cam on the outside of the engine block which should be covered with rubber fittings, then remove the bolts directly on the bottom of the valves then make sure there arent any other bolts holding it on, i'm not exactly sure if there is, then pull up and hope it comes off.

May 03, 2011 | 1981 Suzuki Gs 550 L

1 Answer

I have Suzuki gs 750 e, model 1979. The engine is an air-cooled, 4-cylinder,4-cycle model equipped withdual overhead camshafts. I am looking for new camshafts for the engine. Do gs 1000 and 1100...


The simple answer is no. It is possible to put a complete 1000 engine into the 750. but this will involve making brackets etc.
Proberbly the easiest way to more power is to fit the barrells and top end from the GS850. This will fit straight on. Ideally, you will need the 850's carb, but the 750s could be jetted to suit. The exhaust is the same fittings, so you could retain the gs750 exhaust as well. They also share the same airbox.

Nov 02, 2010 | 1979 Suzuki GS 750 E

1 Answer

I need to know the valve adjustment procedure and


Valve clearance ideal setting is 0.10mm however as ideal replacement size shims are not always available use tolerance 0.05 to 0.2mm inlet and exhaust Procedure remove tappet cover rotate motor to tdc compression (inlet valve lobe pointing to rear wheel and exaust lobe to front wheel) measure clearance if no clearance depress cam bucket hold down by wedging a screwdriver or suitable tool (allen key) between cam bucket and cam remove shim measure with micrometer an relace with a shim 0.15 thinner depress valve remove wedge and measure clearance (if any) repeat procedure 4 each cylinder if clearance to large replace shim with a thicker one till clearance is in spec

Jul 20, 2010 | 1981 Suzuki GS 750 L

1 Answer

Can you use a lock set from a 1980 gs 750 on a 1981 gs 750


seat lock yes, ignition lock if it fits in the hole ,you'll have to get a wiring diagram on line and match the wires by what they operate,if your really lucky wires run the same stuff and are the same color.











9

May 21, 2010 | 1981 Suzuki GS 750 L

1 Answer

Set the cam shaft timing


G'day, from memory the GS you just line up the 't' mark on the alternator flywheel, then put the exhaust cam in with the notch in the right hand end facing forwards level with the head surface, then put the inlet cam in with the notch facing rear-wards, put the tensioner in & double check. I'm not 100% on the direction of the notches, but you can check that the lobes on cyl 1 are both facing evenly away from the valves as far as possible, that should be lined up & away you go, hope this helps :)

Apr 14, 2010 | 1977 Suzuki GS 750

1 Answer

Installing points on a 1979 gs 1000


The points gap is .015 when the cam is at the high point. Parts can be found at www.babbittsonline.com/parts/viewbybrand/parts.aspx No question was asked so I am guessing this is the information you are looking for. Please rate my answer.

Jan 06, 2010 | 1977 Suzuki GS 750

2 Answers

I have a 1977 GS 750 and it runs but it makes a


valve adjust
compression test
carb adjust and timing ck

Nov 12, 2009 | 1977 Suzuki GS 750

2 Answers

I need the wiring color code for the handle bars


google specs for the 750 that will help you out

Aug 17, 2009 | 1978 Suzuki GS 750 E

Not finding what you are looking for?
1979 Suzuki GS 750 E Logo

Related Topics:

742 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4477 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...