Question about 1995 Triumph Daytona 1200

1 Answer

Part help I am working at fixing up a 95 T3 Daytona. The screen trim is coming loose and looking at the parts book there is a Screen Trim Clip T3700057 cheap and I ordered a couple. For the life of me I cannot see how they are supposed to go on and look right. Maybe the part is wrong, maybe the screen trim is too thick as I acquired it. Clip pic is below. If anyone has how they are supposed to look on a 95 Daytona, please send a pic. Thanks.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,336 Answers

I think if memory serves me they clip over the ends of the rubber trim strip where they terminate at the upper fairing. The intent is to secure the ends of the rubber strip to the rear lip of the screen. I threw mine away long ago.

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove headlight housing 2001 FLSTC



To remove the headlamp housing assembly disconnect the wiring harness and then remove the bolt underneath the housing and ligt the housing off the mount.

To change headlamp bulbs:

2001 FXSTD, FXSTS and FLSTS Models

Remove the trim ring screw and then the trim ring, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.
2001 FXST and FXSTB Models
Loosen the trim ring screw and remove the trim ring, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.
FLSTC and FLSTF Models
Except for HDI motorcycles which have a Halogen bulb similar to FXST the FLSTC and FLSTF motorcycles have a sealed beam type headlamp. HDI headlamps also contain a position lamp bulb that is found under the headlamp assembly's rubber boot.
Remove the trim ring screw and then the trim ring, being careful not to bend the two tabs that hold the
top of the trim ring in place, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.

May 17, 2014 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

Headlight trim


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day.How to Solder Pot Metal Headlight Trim
Yamaha Zuma BWS 50cc Headlight Mod works for 125cc too
Bajaj Platina 100 2014 service manual DOWNLOAD FREE FULLMANUALS COM
PLATINA SPC
Bajaj Auto Platina Alloy Wheel Es User Manual

Jan 07, 2014 | 2010 Bajaj Platina 100

1 Answer

How to install gauge trim 2001 harley davidson touring


Take the yellow tape that comes with the trim and throw it in the trash. Put 3 small dabs of RTV sealant on the inside of the trim. Place the trim on the gauge and hold for few seconds. Wipe off any access silicone. Let dry overnight.

Dec 08, 2012 | Harley Davidson Motorcycles

1 Answer

Yamaha 2005 150 HPDI wiring diagram


Yamaha 2005 150 HPDI wiring diagram

Looking for wiring diagrams for digital tachometer with trim indicators and warning signals. Mine had the plastic trip arm break. No trim reading on Tach face. Replaced trip arm forsensor arm and now have no reading on the tach at all except extremely light tach Number. All other electrical components work OK.

Jan 24, 2012 | Yamaha Motorcycles

1 Answer

How to change a headlight bulb on a 2002 Harley Davidson Dyna Wide Glide


REMOVAL

Do not ever touch the quartz bulb with your fingers as fingerprints will etch the glass and cause the bulb to fail prematurely.


FXD, FXDL, FXDX Models

Loosen the trim ring clamp screw and nut, remove the trim ring, pull the connector block from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to unhook and release them from the from notches in the headlamp assembly, pivot the wire retaining clip away from the bulb aqnd then remove the bulb from the headlamp assembly.


FXDWG, FXDXT Models

Loosen the trim ring clamp screw and remove the trim ring, pull the wiring connector from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to unhook and release them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb and remove the bulb from the headlamp assembly.



INSTALLATION

Install a new bulb and assemble the headlamp components in the reverse of the removal process. Align the headlight when it is fully installed. When reassembling the headlamp ensure that the slots and tabs in the headlamp, adapter ring, and trim ring are aligned.

Jul 12, 2010 | 2002 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

I have a 1200. I'm looking for the trim piece, EDGE, of the fairing, left side. Prefer twilight color, but will settle... thanks Don


auto parts store, door guard(trim or piping).comes in colors crome and rubber. it is flexable and can be shaped.

Mar 17, 2010 | 1986 Honda GL 1200 Aspencade Gold Wing

1 Answer

How do I remove the handlebars on a 1998 HD roadking


Remove the cap in the center of the handlebars and take a look, I'm afraid you will have to take the whole housing assembly apart. It's been a few years since I did ours.
Not so easy, first the head light has to come out, the a 5/16 nut inside the head light housing holding on the trim piece that needs to come off. One that's off the plastic trim piece on ignition need to be pried off "gently", then remove the 2 screws and that cover will come off giving you access to the handle bar mounts. Unscrew the old ones at the headstock and put the new ones on where the old ones went and screw them in at the right spot (where you want them) sit on the bike and hang on to them and do them up "tight". Hope this helps! Good luck!

Feb 22, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

How to change windshield on 1994 honda goldwing gl 1500 motorcycle,from stock vented windshield to tall vented windshield.


Carefully roll back the rubber from around the mirror trim rings. Then remove the trim rings. Remove the screw(s) that hold the screen garnish in place. Be carefull when removing the windshield mounting screws that plates don't fall into a place that you won't be able to find them. Assemble in the reverse order. Should only take about 30-45 minutes.

Sep 19, 2009 | 1994 Honda GL 1500 Aspencade Gold Wing

2 Answers

2004 Triumph DAYTONA 600 electrical part


Hello,
This is an old thread but we found the answer after checking if a part no was correct....
The box is an O2 controller for a Dynojet Power Commander kit.
It is used to bypass the sensor that fits into the exhaust to allow full ECU performance/fuel modifying.
Part no 66391201 is also the same compatable part as 76125003 and is used in certain other Dynojet kits. (Daytona 600)
Hope this may help any other Triumph owners with the same question. :)

Apr 06, 2009 | 2004 Triumph Daytona 600

2 Answers

Removal of battery 1999 XJ900Diversion


Take the seat off, then remove the right hand trim panel, there's a couple of screws under the seat and one on the side, the centre rear trim panel needs to be removed as well. There's a couple of locating pegs hidden underneath which are released by pulling the trim gently sideways. Once the trim is off you'll see the battery box with two 10mm locating bolts, the battery comes out to the side.  It's worth getting the remote cables from a battery Optimiser kit fitted when you refit the battery as the terminals can't be reached with the trims in situ. 

Jan 03, 2009 | 2000 Yamaha XJ 900 S Diversion

Not finding what you are looking for?
1995 Triumph Daytona 1200 Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4471 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...