Question about 2002 MZ 125 SX

1 Answer

Carburator How do you clean a motorbike carburetor?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,336 Answers

The First thing you have to NOT DO is try to start it if it has been sitting for any long duration of time 6 months or more second, you have to remove the gas tank, drain the contents, into a can you can see in, look for a dark brown colored corpusal, in the gas, if there is some, that is an indication, that your carbs need to come apart, unless you are a seasoned mechanic, you will have to remove the carb, take the bowl off, of course you will look for the brown couloured substance again, clean the bowl,remove the pin, holding the float in placebeing carfule to secure the needle valve in its proper place after cleaning it thouroughly, remove the jet, using a tiny bit, you reem the jet hole center, taking care not to bore it out, the you run the bit in the jet hole, cleaning any debri that may be there, use carb cleaner and keep spraying it in all in puts and out puts the carb may have, then if you put your mouth to the feul input to the carb, blow in it to be sure it is clear, if not youl have to use carb cleaner and air to clean it out, air and carb cleaner is the key to cleaning it properly, some carbs need to be taken apart and soaked in a carb cleaner, before reassembly, just keep blowing air in all the inputs and out puts, to be sure they are cleared, reassemble and GO,,,

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yardman TILLER 31CC STARTS AND EMEDEATLY DIES


Your carburator is probably gummed up remove it and clean it

Apr 25, 2016 | MTD PRODUCTS INC yardman"" garden tiller"

1 Answer

Fuel system completely flushed carburator completely cleaned, new gas


tank airiation fuel tap filter tankfilter clean? sludge removedl a canister automotive engine cleaner for the fuel are by cleaning carburetor( if there is a L+R re-adjusted) are the gaskets changed and correct placed especially between cilinder and carburetor. there can be especially a small channel in it that it was wrong replaced or is the compression good enough ?
Compression is the very most important thing there is to look at the exhaust site to the piston that must be smooth otherwise there was a problem by overheating piston if there are grooves there can be a wrong adjusting of the carburetor or by a quality problem of the used gas

Apr 23, 2016 | ATVs

1 Answer

I have a Peugeot speed fight 2 50cc motorbike and need to know how to connect the fuel tank to the carburetor please(which pipe goes where).


You may need to ask your question in a motorbike category instead of the 'Chainsaw' one, and someone might be able to help you.

Apr 19, 2016 | Garden

1 Answer

How do you connect the fuel tank to the carburetor(which pipe goes where) on a speegfight 2 50cc please anyone


Please ask your question in a MOTORBIKE category instead of the 'Chainsaw' one and someone may be able to assist you with your question

Apr 19, 2016 | Garden

1 Answer

Having a cut out problem on my honda vt750 going up hills and at haft trottle


Hi, James please disregard the carburetor parts I hope your Holley pump has the same specs as OEM otherwise that could be an issue and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition and leaking.
3. Spark plug gap too close or too wide.
4. Faulty ignition coil, module, and or sensor.
5. Battery nearly discharged.
6. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
7. Intake air leak.
8. Water, dirt, or rust in the fuel system, carburetor and/or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose, dirty, or corroded ignition module connector at crankcase.
13. Faulty MAP, CKP, O2, and/or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damaged intake or exhaust valve.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have nice a day.
VT750 Cuts Out Higher RPMS Fuel Pump
stalling cutting out at power VT750 Ace Honda Motorcycles FireBlades org
http://www.motorbike-forums.com/throttle-hesitation-83-vt750-shadow-t1439.html
http://www.vt750dc.com/ACE_Manual.pdf
http://www.partsfish.com/page/oem-parts-for-honda
http://www.vt750dc.com/VT750C2_OwnersManual.pdf

Mar 24, 2016 | 2001 Honda VT 750 CD Shadow A.C.E. Deluxe

1 Answer

1978 gmc sierra sbc 350.. problems starting its been sitting for a while. I replaced the mechanical fuel pump but still doesn't run. I can pour gas in the quadrajet carburator and it will turn over and run...


If it runs when you pour fuel in the carburetor, then the problem is that the engine is not receiving fuel. (by the way, be careful, the carburetor may back fire and cause a fire). Disconnect the fuel line from the carburetor and place the end of the line in a bucket, then turn the truck over to see if fuel is flowing. If it is a mechanical fuel pump it should pump fuel into the bucket when the battery turns over the engine. If you had a lot of debris pop out of the carburetor, it should be taken off and cleaned. You may have had a bird or something else try and build a nest in it.

Aug 09, 2014 | Cars & Trucks

1 Answer

2013 Hyosung motorbike(150cc). I put diesel fuel in my tank by mistake, and now it won't start. How do I drain the fuel to get the correct fuel in there?


You will need to take the fuel tank off and empty it, rinse it out with some gasoline, then disconnect the fuel line at the carburetor and drain, then drain the carb bowl by taking the bleed screw out of the bottom. Re install everything. Refill the system. Remove spark plug and clean it, or replace it. Then keep cranking till it fires up and you run the remainder of the diesel out. Recommend adding an octane boost supplement with first tank full of gas, or use premium.

Jul 21, 2014 | Cars & Trucks

1 Answer

Gentron 10000w generator has a leaking carburator


Your carburetor float valve may be stuck open. You'll have to remove the carburetor, remove the sediment bowl at the bottom of the carburetor (where the float is), and check the float. Is it filled with gas? Replace the float if it is. If the float is dry inside, then remove the float and clean the needle valve & seat. (be careful to note how the float pin, linkage, spring, etc. are positioned so you properly reassemble. After cleaning & reassembling, turn the carburetor upside down & try blowing into the gas line connection on the carburetor. You shouldn't be able to blow air. Turn the carburetor right side up & repeat. If you can blow air into the carburetor's gas line connection, the float valve & seat are properly working. Reinstall the carburetor. You should be good to go.

Dec 03, 2013 | Gentron 10,000W Generator with Electric...

1 Answer

Revving engine gpr 125


Hi, Reece very scary it does happen from time to time on all motorcycles your reaction was great in killing the engine usual suspects are a rusted/bound throttle cable, a stuck carburetor slide, or broken return spring/cable on the carburetor or throttle body for injected models sorry you can't find the first and best tool you ever bought for your Derbi despair, not for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Derbi GP1 125 250 Workshop Manual
https://www.oemmotorparts.com/oem2.asp?M=Derbi
http://www.derbi.com/fr/images/stories/modelos/37/manual.pdf
Derbi GPR 125
Tips Tricks

Jun 29, 2013 | Derbi Motorcycles

Not finding what you are looking for?

Open Questions:

2002 MZ 125 SX Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top MZ Experts

Luc Francoeur
Luc Francoeur

Level 2 Expert

102 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Jay Finke
Jay Finke

Level 3 Expert

1224 Answers

Are you a MZ Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...