Question about 1980 Laverda 1000 Jota

1 Answer

Indicators A small prolem has arisen. the indicators will not flash

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,336 Answers

They light up bright but no flash. Checked the earths the battery voltage is 12.5V engine off checked the flasher unit which works on my old landrover. What could be the reason?ry cleaning the contacts on the bulbs - often they will not flash if one is burnt out or not making proper contact. You can also try and clean all the earthing points.,,,

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kymco Stryker that I have just replaced the indicators on, but, they don't flash they are on just like the light would be. I need to find the relay but don't know where to start, can anyone h


did you replace the whole indictator assemblies or the bulbs and are they l.e.d indicators you have on it now and was it using l.e.d ones originally

Jan 09, 2015 | Kymco Stryker 125 Motorcycles

1 Answer

Replaced Aprilia rs50 2006 indicators with LED ones + LED flasher relay though they light up but DON'T FLASH?


I am not a electronic wizz but i believe the led's will light up but do not have enough resistance to cause the internal breakers to work.
I found this.
The post that had the link said that it fixes fast blink and no blink conditions. http://www.greggscustoms.com/instruc...istor_Inst.pdf

Oct 13, 2012 | 2007 Aprilia RS 50

1 Answer

Honda cbr indicators all flashing


Hi, led bulbs have much lower power consumption than common bulbs. Usualy when you change for this type of bulbs you also need an apropriate flasher wich you did, but question the suplier about it. another solution is to instar a resistance just before the bulb in order to increase ohms ans all be normal again.
good luck
Francisco

Oct 20, 2011 | Motorcycles

1 Answer

My indicaters flash when arming the alarm but not when signaling right or left ihave a o9 yamaha fz1s


The indicators are wired in to the alarm wires in the loom, i would suggest you check the signal fuse, and the relay, poss switch, do the indicators *** on but not flash? If not and the fuse is ok remove flasher relay and join the wires together if the indicators light this proves the circuit is ok and the relay must be at fault,are the indicators standard, or led

May 13, 2011 | Yamaha Akros Tec 50 Motorcycles

2 Answers

Have installed led indicators to kawasaki zx6 2004 model now flash rate too fast


Flashing too fast indicates too much current flowing and this would point to a bad bulb or shorted socket. Maybe a grounded wire in the circuit. Check these items with a DVM....

Feb 21, 2010 | 2004 kawasaki ZX-6R

2 Answers

How to connect buzzer to indicators on Honda Deauville 700 motorcycle


if you have a single dash indicator on your bike you can pick up the signal from there.
If not you can install two small buzzers or one buzzer with a diode to each of the signals, this will prevent a back feed and flashing all the lamps.

Hope this helps.

Jul 07, 2009 | 2007 Honda NT700V Deauville

1 Answer

All 4 indicators flash at the same time,


Hi Richard, Just a thought, I had a similar problem fitting Led bulbs to my Volvo and sorted it by putting the correct resistors in line.
Beware these get very warm so need safe/cool area for mounting.

Dec 30, 2008 | 1988 Suzuki GSX-R 750 J

2 Answers

LED Indicator Problems & Flasher Relay?


Modern Ducatis (and cars) don't have a conventional flasher. The blink rate is controlled by the dash cpu. The blink rate change is used to indicate that a bulb is out (by sensing low resistance). Using a resistor will fool the cpu into blinking correctly.

Nov 20, 2008 | 2008 Ducati Hypermotard

Not finding what you are looking for?
1980 Laverda 1000 Jota Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Laverda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

Rigger

Level 3 Expert

856 Answers

Andrew Smart
Andrew Smart

Level 2 Expert

230 Answers

Are you a Laverda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...