Question about 2003 Hyosung GT 600 Comet

1 Answer

MOT Test Does someone know which things are cjecked on the MOT Test?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

A) Sitting on machine check:1. All controls switches and horn 2. Front suspension forks handlebars and head bearings. b) At the front of the machine check: 1. Front lights and indicators 2. Front brake master cylinder (if fitted) c) Place the machine on its stand and raise front wheel check: 1. Steering, front forks and head bearings 2. Front brake and wheel bearings 3. Wheel and tyre condition. d) Lower front wheel and go to right side of vehicle and check: 1. Frame, VIN, seat and foot rest 2. Exhaust system 3. Final drive (if fitted to RHS of machine) 4. Rear wheel, tyre and brake e) Raise the rear wheel and check: 1. Rear wheel, rear brake/components and tyre condition. 2. Rear suspension and final drive f) At the rear check: 1. Rear position lamp(s)/stop lamp(s)/reflectors and indicators. 2. Rear suspension. 3. Registration Plate g) On the left of the machine check: 1. Frame and foot rest 2. Exhaust system 3. Final drive (if fitted to LHS of machine) 4. Rear wheel, tyre and brake. h) At the front of the machine check: 1. Wheel alignment 2. Headlamp aim 3. Brake performance,,,

Posted on Nov 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Hi, I have a 1998 1.3 Suzuki swift that has a violent wobble at the front end. its not tires, balance or bearings as this was all done in its mot last week. cant seem to see any obvious problems with parts...

the mot dont prove anything much>?
you do know that a real shop , not mot goofs.
a real ASE shop would attempt a in car tire balance
and it would either fail, or they would see the obvious , pronto.
for readers, MOT is "SMOG TEST STATION" in English.
Site side, they are NOT technicians At all, they just do their simple tests and give you thumps up or down.

what can it be, (first end this assumptions deal, keep a 100% open mind, only the truth will come out)
1: bad balance or bad shocks, (dampeners)
a tire that is just tiny bet out of balance will be 10x magnefied
with bad shocks, since 1920 to now. no changes....

2: ; bad wheel bearings.
3: bad supspension parts. lose, bent, bushings bad etc.
try a suspension shop, ask for them to check the front end parts.
5: bad drive. CV joints, or axles bent or bad.
again any real ASE shop can find this easy. Not the MOT s

Oct 04, 2013 | Suzuki Swift Cars & Trucks

1 Answer

1987 300zx rust problem

OLD CAR. Depends how bad the rust is, do you need new panels or can you fill the holes themselves with filler ? Main thing is would it pass a MOT Test. Japanese Cars in the 70s & 80s were made from recycled steel, they were all prone to rust.

Jul 23, 2012 | 1984 Nissan 300ZX

1 Answer

My renault Megane RT 1.6 twin Cam T reg has just failed its Mot emission test Fast Test was OK but failed on Idle Test. Carbon Monoxid to high at Idle Speed reading 1.73 when it should be 0.50 max. I...

if there are no faults showing, then the most obvious thing to do would be to change the air filter, this is a relatively cheap part, but it can make a huge difference to emissions, even if it looks perfectly clean.
also make sure you take the car on a good run before taking it to the test centre to ensure that the engine and catalytic converter are up to operating temperature.

it is possible that the catalytic converter is clogged up and not working properly. the only cure for this is to replace it. the mot tester can usually tell you if he thinks it is the cat. my mot tester is always good for advice, just ask what he thinks could be causing it if the air filter does not make enough of a difference

Apr 12, 2011 | Renault Sport Cars & Trucks

1 Answer

Hey there, you seem to know what you are on about i have a problem with my dt 125 re 2004. It had been sat for about 3 months before i bought it, and it ran fine when i got it did not ride it but it...

Where is the black liquid? In the fuel tank? Over the engine?
Please explain where and what you think it is.
I presume it passed the MOT and it isn't someone who is jealous of it.
Thank you

Nov 27, 2010 | Yamaha DT 125 R Motorcycles

1 Answer

I have an S reg 1999 ford fiesta 1.25 Ztec i recently took it for an MOT and it failed because of extremely high emissions. i have changed the lambda/oxygen sensor, given it an oil change with filter, new...

this possibly will be the MAF sensor or even the throttle itself, auto choke are a bit of a pain on fords and tend to stick the best way would be to take it to a place where they have equipment to test these things on i am surprised the mot center didn't tell you what the problem could be what is causing it to do it so you can get it sorted..but anyway sounds like the MAF might be playing up...hope this helps

Feb 18, 2010 | 1993 Ford Festiva

1 Answer

Car failed MOT on emissions yesterday but after a

Several things.....

EGR Valve
Bad Spark Plugs
Bad EVAP Canister.....

All related items to fuel and spark.

Do you have bad fuel mileage? How does the engine run? Smooth? Chugs? Idles rough?

Oct 01, 2009 | Daihatsu Charade Cars & Trucks

2 Answers

Ford failed MOT on High CO emission

High CO usualy means the O2 sensors are not reading properly. Take it to a parts store that can read codes, I know Auto Zone does in my area. If it is the O2 sensor it is an easy fix but the sensors run about $50.00 each.

Apr 18, 2009 | 1995 Ford Escort

1 Answer

Lambda probe fault possibly

I bought a 2000 polo 1.4 yesterday after having an MOT. The warning lamp came on today but the car is running fine. Whether its the Lambda sensor or just the light itself is a common fault, I think garages turn off the lights to get it through the MOT then they come on again in a day or two!

Mar 29, 2009 | Volkswagen Quantum Cars & Trucks

1 Answer

Ford Mondeo failed its MOT exhaust emisson test

The advice that the garage gave you seems right. If any bushes were worn they would show up on the MOT Test. Try taking it to another garage to check out the Cat for your peace of mind.

Nov 21, 2008 | 2000 Ford Escort

2 Answers

Mot failure on emissions

make sure to smell the oil and see if it is contaminated with fuel
if it is then do an oil change and try to re test

May 27, 2008 | 1996 Toyota RAV4

Not finding what you are looking for?
2003 Hyosung GT 600 Comet Logo

364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides