Question about 2008 Husaberg FS 450 e

1 Answer

Hot brakes I noticed today that after stopping

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

My front disk brake was hot. When i parked my bike in front of my house I heard that dissipating heat ticking that would normally be associated with a hot engine only it was my front disk. This was just from everyday ride through town. I never noticed if car rotors got hot so I have to ask if its normal for a bike rotor to heat up after some use? It was too hot to feel with your hand but not glowing red or smoking. Nor did it give the aroma of toasted brakes.It will generate heat normally. Lift the front end and spin the wheel to see if your pads are dragging.,,,

Posted on Nov 10, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 dodge neon my brakes are not working, i do have break fluid

If he just poured brake fluid in the system will need to be bled of air. Air, unlike liquid, is able to be compressed and accounts for the "weak" feeling in your brakes.

To bleed the brakes, you'll need two people. One person to open the bleeder screw at each wheel, and another to pump the brakes from the driver's seat. When bubbles stop coming out of the bleeder port, close it back up and move on to the next wheel. Make sure the reservoir doesn't run dry while you're doing this.

Jan 24, 2014 | 2003 Dodge Neon

1 Answer

Brake pedal just started needing to be pumped to engage and smoke coming from behind the back drivers side tire

I have the same truck! You could have a leaking wheel cylinder. Look at the brake drum on the driver rear and see if its wet. also check your brake fluid level. If you are leaking you will be low.
Wheel cyl's are not super hard to do, just make sure you do everything and both sides. also do one side at a time so you can use the other side for reference when putting it all back together.

Jun 18, 2013 | 1987 Nissan Pickup

1 Answer

I have a 98 ford F150 4x4 and the brake pedal lights had been staying on after i stopped and shut down the truck.Had to pull pedal up to shut them off. today i noticed a shaking in rear brakes and pedal...

you may have a bad master cylinder that is not pushing the brake pedal to the stop when not other words the master allows the pedal to rest lower as it doesn`t have sufficeint residual pressure to push the pedal back,or the pedal is catching on something not allowing it to return to its rest position.this can cause the rear brakes to apply slightly as the pedal not being all the way in the rest position is applying just enough pressure to the system.if the pedal is going all the way to the floor then you need to check for a fluid leak in the system including the master cylinder(internal leak)if no external leak is found.

Apr 28, 2011 | 1998 Ford F150 Regular Cab

1 Answer

Hi my name is Jessica, today I noticed that my 2000 Ford Windstar started shaking when I come to a stop, and is really slow to accelerate, any help would be sinserly appreicated..

Sound like you have a brake issue when you apply the brakes sounds like a rotor may be hanging up not letting go causing the van to be sluggish to take off holding it back

Mar 25, 2011 | Ford Windstar Cars & Trucks

1 Answer

Engine code 1759 on 2005 Nissan Pathfinder, I live in AZ and when it gets over 108 my car does not want to accelerate when I start from a stop. Today I had the transmission fluid checked and the fuel...

I also have a 2005 pathfinder. I just, today, got p1757 and p1759. I am having the same problem you described. I also noticed the tempature difference. I live miami, fl. I read something about front brake valve solenoid forcing the transmission into a safe mode so there is no pick up. What did you find if anything? Any solutions? Any advice?

Jul 02, 2010 | 2005 Nissan Pathfinder

3 Answers

My brake light on my Kia spectra is constantly on. Today I noticed that I had to press the brake all teh way to the floor to have it stop.

check with consumer reports. there was a recall on certain year, yet can't recall which one at the moment. hope this helps.

May 10, 2009 | 2003 Kia Spectra

1 Answer

Ford Fiesta Encore 1996, 1.3. brake problem

if the pedal is verry hard to push then you have lost vacum to the brake booster or the booster has gone bad.

May 05, 2009 | Ford F Cars & Trucks

1 Answer

2000 chevy cavalier brake problem

the brakes will get hot ??? before you go any further drive it around then stop on a level road and try pushing the car to see if the brakes are binding,noise from brakes at front ??? were the disks worn or grooved ??? what make of pads have you used ???are they too hard for the car ??how much copper in the pad material??were they made in china???have a good look

Jan 13, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
2008 Husaberg FS 450 e Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

68082 Answers

Sean Colbert
Sean Colbert

Level 1 Expert

17 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides