Question about 2008 HM CRE F450XI

1 Answer

WONT START My bike was working fine last Thursday when I took it for a ride and filled up the gas tank. However

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

When I tried to start it yesterday it would not start; pushing the ignition causes just one *click* sound and then nothing. The battery is reading 12.65V or so so that seems fine. I did some research and I think it's either along the lines of the spark plug(or ignition area) or maybe water in the float bowls from fueling up(?). I tried it again today and this time there was no *click* sound. I also noticed that the -neutral- and -check engine oil- lights which normally light up quickly at start up take a few seconds before lighting up. Now I think it's more in the electrical section but not exactly sure which area. I'm going to take a look at the spark plug and maybe try to drain any water out, but was wondering if anyone had any other ideas? ,When you press start, the churning sound you (typically) hear is from the starter motor forcibly turning the crankshaft. While the starter is physically turning the engine, the engine is also injecting the fuel/air mixture into the cylinders and firing the spark plugs. If the plugs successfully ignite the incoming fuel/air mixture, the engine will begin turning itself over. If you press the button and nothing happens, or you just hear a click, the starter motor is not cranking the engine. The click you heard was probably the starter solenoid attempting to engage the starter to the flywheel of the crankshaft. The problem is probably the starter. It may be a bad battery. Reading the open voltage with no load on the battery tells you nothing. Put the voltmeter across the battery terminals and read the voltage while holding the Start button.,,,

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bike cuts out on half a fuel of tank


Yes There is a vent in the fuel tank. It is either in the filler cap or a separate hose. Sounds like ti is plugged up.

Mar 25, 2014 | 2012 Piaggio Fly 150

Tip

How to store your motorcycle for winter. Storing your motorcycle.


As the summer months start to come in, we all like to get our motorcycles out and start riding them, but i hear a lot of people saying help, my bike wont start! That is because when you last parked it in the shed for the start of winter, then you made no preparations. With a few simple steps, next summer, you can get your bike out, and fire it up without any problems, ready to ride. There are things you must do when you go into storage, and a few things to do when you bring your bike out.
OK,so winter is approaching, and you want to put your bike away in the shed.
First thing you need to do is drain some fluids. Drain your engine oil. Then drain your gas tank and carburetors. It is important to drain the carbys, as the fuel left in the float bowl will go bad. You can choose to totally drain your gas tank, or fill it to the top with gas. Storing a tank full with gas, leaves no room for moisture to form, causing rust on the inside of steel tanks. Next, you need to also disconnect one lead from your battery, or even better, if you have a trickle charger hooked up to it. Thats about it really. Also,if you are confident in doing so, remove spark plug, or plugs, and spray some penetrating oil down into each cylinder, turn engine over to work it through. This will prevent any moisture or corrosion from forming on the inside of your cylinders. It is also a good idea to clean or replace your spark plugs each year anyway.
Now it's summer, and you want to ride, just roll your bike out. Put in some fresh engine oil, a fresh tank of gas, and a fully charged battery, you are ready to go!

on Jun 21, 2010 | Motorcycles

1 Answer

I have a 2000 zx12 left to me from my family member passing away. the bike set for 6 years i replaced the fuel pump and gas tank the old tank still had old gas. the bike started and ran fine. one day i...


You should have the injectors cleaned, As fuel gets old, the most burnable part of it evaporates This leaves a very liquid gunk behind, the gunk contains some very big bits of rubbish, (compared to clean fuel or injectors) it sounds as though you have blocked injectors. If you give them a good clean and fill the tank with new fuel you should fix the problem.

Apr 14, 2012 | 2000 kawasaki ZX-12R

1 Answer

Pulling


adjust the slack in the brakes as too tight can make the brakes ht & expand thus engage slightly!

Jul 26, 2009 | 2008 kawasaki Ninja 250R

1 Answer

1973 CL100 Scrambler, died while riding, won't start


Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side or bottom of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine.

A “very helpful” rating for this answer? Thanks!

4d292be.gif

Jul 01, 2009 | 1973 Honda CB 100

1 Answer

83 honda cx650 smoking one day not the next


The sputtering was a bit of water in the bad gas you got and the smoke was probably from a bit of diesel fuel that was put into a gasoline storage tank in error. The temp guage going bad is just one of those things that happen from time to time, probably just a bad sensor. The idle speed change is a bit quirky but easy to adjust. Stick a fresh set of plugs in the bike and the starting problem should clear up.

A “very helpful” rating for this answer? Thanks!

Jun 24, 2009 | 1987 Honda CBR 600 F Hurricane

2 Answers

No power when going into 2nd gear or higher


Forget the wiring. The key thing here is probably the painted gas tank. In all likelihood there was some trash that got into the tank related to the paint job. Do this > Carefully remove the water trap bowl from the petcock, (gas valve), and look inside the bowl. It may have some water in the bottom and some trash on top. Clean the bowl. Next, remove the petcock and clean it as well. Drain the carbs. Turn the gas on and wait a minute for the float bowls to fill.

Give it a try. It may be that the gas from the tank is restricted and can't refill the floats as fast as the engine needs. A second thought is the exhaust pipe. The bike will not run well if the exhaust is partly plugged up. Disconnect the exhaust and tick off the neighbors by going around the block without a muffler. The inside of the muffler may have collapsed when the welding was done.

Between the two solutions I think the exhaust is the more likely.
Please rate this solution as " FixYa " if you go riding tomorrow.

Mar 24, 2009 | 1982 Yamaha XJ 650

2 Answers

Breaking Down


The problem may be a pinched fuel or vacuum hose, or a weak/collapsed vacuum hose. The problem may be varnished fuel/carburetors. It may be an electrical problem: loose connector or defective conductor. I cannot help you other than this without having the Duc and performing a few tests. The Monsters are fun to ride.

Nov 20, 2008 | 2008 Ducati Monster 696

1 Answer

Bike wont start


when I tried to start it yesterday it would not start; pushing the ignition causes just one *click* sound and then nothing. The battery is reading 12.65V or so so that seems fine. I did some research and I think it's either along the lines of the spark plug(or ignition area) or maybe water in the float bowls from fueling up(?). I tried it again today and this time there was no *click* sound. I also noticed that the -neutral- and -check engine oil- lights which normally light up quickly at start up take a few seconds before lighting up. Now I think it's more in the electrical section but not exactly sure which area. I'm going to take a look at the spark plug and maybe try to drain any water out, but was wondering if anyone had any other ideas? ,When you press start, the churning sound you (typically) hear is from the starter motor forcibly turning the crankshaft. While the starter is physically turning the engine, the engine is also injecting the fuel/air mixture into the cylinders and firing the spark plugs. If the plugs successfully ignite the incoming fuel/air mixture, the engine will begin turning itself over. If you press the button and nothing happens, or you just hear a click, the starter motor is not cranking the engine. The click you heard was probably the starter solenoid attempting to engage the starter to the flywheel of the crankshaft. The problem is probably the starter. It may be a bad battery. Reading the open voltage with no load on the battery tells you nothing. Put the voltmeter across the battery terminals and read the voltage while holding the Start button.,,,

Nov 10, 2008 | 2007 ATK 450 Motard

Not finding what you are looking for?
2008 HM CRE F450XI Logo

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top HM Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4481 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Angelo Stewart
Angelo Stewart

Level 2 Expert

224 Answers

Are you a HM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...