Question about 2006 Hero Honda Super Splendor

2 Answers

Starter problem I have noticed

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Dear sir,y self start not working sum time,,IT IS NEW BATTERY PUT IN HERO SERVICER CENTER

Posted on Jun 02, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Most of the times recently the auto start does not work . I contaced the service man he is now recharging the battery . Did the wrong usage of auto start ( pressing the button and accelerating at the same time ) cause the problem only later I knew the pressing of button only suffices the start ,Generally speaking, revving the engine at start-up isn't good for the motor. It's best to let it warm up a bit before cracking the throttle. It sounds as though the battery was just weak. The only thing that will result from pressing the starter button and twisting the throttle at the same time is additional wear on your engine (and maybe the starter motor too).,,,

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 pontiac montana and am trying to figure out how to change the starter.


STARTER REPLACEMENT (ENGINE ELECTRICAL) Document ID# 688149 Starter Replacement

Removal Procedure

Important: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.
  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.


  3. Remove the starter motor BAT terminal nut and electrical leads.
  4. Remove the starter motor S terminal nut and electrical lead.
  5. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  6. Remove the starter motor bolts.
  7. Remove the starter motor.

Installation Procedure



  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in Cautions and Notices.
  3. Install the starter motor bolts.Tighten:
    Tighten the starter motor bolts to 47 [n-m] (35 lb ft).
  4. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  5. Install the starter motor S terminal electrical lead and nut. Tighten:
    Tighten the starter motor solenoid S terminal nut to 3 [n-m] (27 lb in).
  6. Install the starter motor BAT terminal electrical leads and nut. Tighten:
    Tighten the starter motor solenoid BAT terminal nut to 10 [n-m] (89 lb in).
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.

Aug 05, 2016 | 2001 Pontiac Montana

1 Answer

Starter fuse location and strater relay


In most newer cars the starter fuse is a fusible link or in a fuse panel under the hood. Fusible links are often difficult to find because they look like a barely noticeable bump in the wire. The starter relay/solenoid is typically an assembly that is part of the starter motor.

Aug 17, 2014 | Cars & Trucks

1 Answer

Replace starter


Remove the negative battery post. Remove the wires from the starter after noticing where they go. Remove starter. Replace everything in reverse sequence that you removed it.

Sep 07, 2013 | 2006 Ford Taurus

1 Answer

Starter wont engage after replacing dead battery


Check power to starter motor solenoid, solenoid operation and starter motor voltage during cranking. If the starter motor is receiving power from the solenoid, but isn't cranking, then replace the starter motor.

Also check the condition of battery terminals, wiring and connections. Also check the earth wire from the body to the engine.

Nov 12, 2012 | Cars & Trucks

2 Answers

I've noticed the starter drive gear does not stay engaged On the E-Drive starter with the flywheel if the engine does not start as in the older Prestolite style starters. Why?


Becausethe starter drive gear disengages after each starting attempt, the engine ismuch easier to hand prop should the battery be too low to provide normalstarting voltage. Though we do not recommend had-propping an engine, it doesoccasionally still happen in the field.

Jul 09, 2012 | Sport & Outdoor - Others

1 Answer

My 2000 Mitsubishi Eclipse V6 engine, failed to start. It had no noticeable problems leading up to the complete break down. I did notice smoke coming up from the hood when i was stopped at a stoplight a...


probably starter check to see if you have power to the starter because you do have a fuse and a starter relay also.any auto parts store nowadays can bench test your starter so i would advise taking it off and having that done first.






TIM.

Oct 20, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Engine won't start


maybe that could be check for that fuse if it is busted.if your starter will crank and still the engine will not start then check if there is current coming from your high tension wire of your distributor assembly.if there is no current check for the connection or fuses.

Dec 28, 2008 | 2000 GMC Sonoma Extended Cab

1 Answer

7.3 oil leak above starter head area


pull insp. cover sounds like rear main seal

Dec 14, 2008 | 1999 Ford Escort

1 Answer

Cranking


Yep....unless you are a mechanic you need to take it to a repair shop (does not sound like you are). The click click is indicative of a starter problem....if a wire burned (and it was any one of those to the starter the starter would probably not have worked at all...sure the blackness was not grease oil and roaddust mixed together.

Jan 11, 2008 | VMware P2V Assistant 2 Starter Gold...

Not finding what you are looking for?
2006 Hero Honda Super Splendor Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hero Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

chris

Level 2 Expert

232 Answers

Are you a Hero Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...