Question about 2003 Hartford HD-125S
But when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,
Posted on Nov 10, 2008
Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!
Posted on Jan 02, 2017
SOURCE: battery
but when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,
Posted on Nov 10, 2008
SOURCE: battery
but when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,
Posted on Nov 10, 2008
SOURCE: battery
but when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,
Posted on Nov 10, 2008
SOURCE: battery
but when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,
Posted on Nov 10, 2008
SOURCE: battery
but when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,
Posted on Nov 10, 2008
Nov 10, 2008 | 2005 Vertemati E501 E
Nov 10, 2008 | 2001 KTM Adventure R 640
Nov 10, 2008 | 2003 KTM 625 SXC
Nov 10, 2008 | 2002 Husaberg FS 400c
Nov 10, 2008 | 2002 Husaberg FE 650s Dirt Tracker Black...
Nov 10, 2008 | 2000 Husaberg Fe 600 E SM
Nov 10, 2008 | 2006 Husaberg FE 550 e
Nov 10, 2008 | 2000 Husaberg Fe 501
Nov 10, 2008 | 2000 Husaberg Fe 400
Nov 10, 2008 | 2003 Husaberg FC 550 -6
Apr 19, 2018 | Motorcycles
Apr 18, 2018 | Yamaha Motorcycles
112 people viewed this question
Usually answered in minutes!
×