Question about 2008 Gas Gas EC 250

1 Answer

Brake light

Hey guys

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

I am trying to hook up my Acerbis LED tail/brake light to my '01 EC250. I can get the tail light to work but not the brake light. I am running the all stock electrical except for the headlight and tail light are Acerbis units.I guess is if anyone has any experience with this tail light set up? I spent all day trying to figure this puzzle outIf you have the wiring hooked up as described in the previous post try hooking the tail lamp wire up to the brake lamp. Does it work then? If so the brake switch may be defective. If not then either a bad ground or switch. Trace the wiring from the brake switch to the connectors and unplug it. You will need to test it with an ohmeter and see if it is turning on and off as you work the brake. If the switch is working you either have an open wire or the brake light bulb ground is not good.,,

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey guys I've got a 1995 hasqvana 610 te when the


put it on craigslist and take 700 for it to a guy who will blow it up the next day

Mar 30, 2012 | 2000 Husqvarna TE 610

1 Answer

2011 yamaha fz6r brake light does not work bulb is still good where could the problem lie?


There is a switch that turns the brake light on that is connected to the rear brake foot pedal...check the wiring on this switch and if the wiring is ok, then you will need to test the switch to see if it is good...you can test the switch with a continuity tester...or have someone with one check it for you....the guys at autozone have these testers if you cannot obtain one...anyway, the switch will show open when the bike is just standing there and it should show closed when you depress the brake footpedal

May 26, 2011 | 2011 Yamaha FZ6R

1 Answer

Hey i'm having some trouble getting pressure in my front brake after having bled the old brake fluid and replaced it with new and then bled out any excess air. I am pretty certain that there is no...


Im not to familure with these bikes, im more of a harley guy, but i have a couple suggestions:
1. You may not have air in the lines (air bubbles may not surface the master cylinder) but, I have seen where air gets trapped in the caliper, or banjo bolts. Try when blleding them, when you put prssure on the lever, crack the banjo bolts and tighten, then pump them up again.
2. Same thing, I have also seen air trapped in the master cylinder, try bleeding the banjos again.
3. Make sure the brake disk is still has plenty of thickness, and your not right at or below the service limit.
4. If you have a 2 piston or 4 or 6 piston caliper, make sure when you pull in the lever, all your pistons are coming out and sucking back in evenly.
5. Make sure your using the correct brake pads.
6. Always make sure your using the correct DOT brake fluid, its very dangerous if you dont, and can KILL YOU.

Hope this helps some.

May 12, 2011 | Hyosung SMR 510 Motorcycles

1 Answer

Electronic clicking...won't start...??..


Dead/low battery, system won't engage the starter because there isn't enough voltage

May 04, 2010 | 2003 Ducati 749

3 Answers

I have an 1985 GoldWing Interstate with a trailer hitch. When I apply front brake, the front running lights as well as the dash lights go on. Other wise, the lights most time do not show. Also, when I...


Check your trailer connector, you have a short circuit between the brake and tail /marker lamps. or water in your tail/brakelamp. Also check both brake switches, for water or corrosion.

Mar 29, 2010 | 1985 Honda GL 1200 Interstate Gold Wing

1 Answer

Brake light


front brake lever not depressing brake light button. inside throttle housing or I had a guy the other day thought brake light was stuck on (found burnt fillament brake light)

Feb 09, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Rear Brake recall


If there's a recall for your bike, go to this link and enter your info, it there is a recall on the brakes it will be listed. https://www.harley-davidson.com/EX/MNT/SCHK/en/servicecheckup.asp?locale=en_US&bmLocale=en_US

Nov 20, 2008 | 1993 Harley Davidson XLH Sportster 883...

1 Answer

Brake Noise


my rear brake squeals too. not worried. I only use it on hills.

Nov 10, 2008 | 1990 Ducati 750 Sport

Not finding what you are looking for?
2008 Gas Gas EC 250 Logo

Related Topics:

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gas Gas Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4477 Answers

Luc Francoeur
Luc Francoeur

Level 2 Expert

102 Answers

Kim Halliwell

Level 1 Expert

31 Answers

Are you a Gas Gas Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...