Question about 2002 Ducati Monster 750 i.e.

1 Answer

Clutch Hello

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

I've got a 98 Monster 750. I just replaced the Slave Cylinder with an aftermarket Moto Wheels Slave Cylinder and now the clutch wont engage. I've bled the system and the Clutch Lever seems to have appropriate resistance. However the clutch won't engage. It has a very weak feeling of pulling when it's in gear but throttle input does not affect it. Thanks to anyone and everyone that can help.Have you checked with MotoWheels about their unit? They'd know it best, and could hopefully shed some light on it. What kind of bleeder did you use? I've had the best luck with a MightyVac set up, where you draw the fluid out from the bleed screw, rather than pump the lever.,,,

Posted on Nov 10, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Clutch is slipping after replacing clutch plates and springs

Hello and thanks for the question.
Your CBR1000F has a hydraulic clutch and may have a problem with the hydraulic system. I assume that the cluch plates and springs were installed properly.
I would flush out the hydraulic system first with fresh fluid and make sure that the line is free of air and the lever feels smooth and strong. The master cylinder may have become corrodd and plugged up over the years. If the hydraulic system is working properly you should go back to the clutch and check for improperly installed plates or excessive wear on the clutch center or the clutch basket.

If you have a continued problem please contact me back.

Thanks and I hope that this helps.

Feb 05, 2011 | 1990 Honda CBR 1000 F

1 Answer

Zx-9r 2000 how do you remove the clutch side cover to change the clutches

The clutch cover is removed in a two step process.
  • Remove the clutch cable by loosening the adjustment at top and bottom first. Then remove the cable end from the clutch lever. This should give enough slack to remove the cable at the bottom by the clutch cover. ** Take notice of the angle of the lever that the cable goes into the cover. You will want to re-assemble the clutch cover with that lever in the same angle.
  • Remove the clutch cover bolts around the outside of the cover.the cover should now be removed by pulling the cover straight out.

Thanks and I hope that this helps.

Jan 21, 2011 | kawasaki ZX-9R Motorcycles

1 Answer

Honda nifty bfifty clutch slip, how to adjust or is it oil filled centrifugal clutch, if so how do u fill

Hello David?
Motorcycles have what is called wet clutches. The clutch is bathed in the engine oil(crankcase oil ) To ck the adjustment, squeeze the clutch lever enough to take up any slack. There should be at least 1/4 in freeplay. If no free play the clutch will slip. Too much free play and the clutch won't dis-engage.after verifying free play, Take this part with serious thought. Wet clutches do not like motor oil. It causes the clutch to slip. So, If you have changed oil or have added any and it was not motorcycle engine oil, It is more than likely your problem. You will need to drain the oil and filter and put the right type into the engine. The clutch has np separate oil supply. Lever adjustment should be at the clutch lever clamp. Now what is this 50/50? Good Luck-

Jan 01, 2011 | Honda Jade Motorcycles

2 Answers

Hello, Clutch not disengaging properly

it looks like you have worn clutch plates very common on learner bikes. but do try to adjust the clutch cable first by winding the adjuster on the clutch lever. if this fails drain the eng oil and remove the left hand eng cover to get at the clutch plates. remove the springs by turning retaining bolts about 6 of them. then your clutch plates will slide out off the drum any bent steel plates even a little replace. any dark or burnt friction plates also replace, usually done all in one go and quite cheap to do . fit new parts in exactly reverse order dont forget new oil re set cable and off you go p.s also check clutch basket for tiny notches from plate wear if very little a gentle file will sort this

Feb 12, 2010 | 2006 Hero Honda CD Dawn

1 Answer

03 zx12r clutch wont disengage

the clutch disks are stuck together

Apr 21, 2009 | 2003 kawasaki ZX-12R

2 Answers


sounds alot like the hydraulic clutch system may need to be bled and possibly the master cylinder cleaned. these clutches usually withstand alot. and considering the age of the bike. if the master cylinder for the clutch has not been gone through recently i would consider focusing efforts on it, and bleeding the system for any air that can cause the clutch not to disengage fully.

Mar 24, 2009 | 1987 Honda VT 1100 C Shadow

1 Answer

I have a ´06 Vthunder, when going on 4th or 5th gear and try to recover speed the clutch seem to be engage, you can hear how the RPM goes up, but no speed change, by the way, no adjustment left on the...

hello. it seems that the clutch is starting to wear significantly. the best you can do is make sure that there is freeplay left in the clutch lever. but if no more can be had then it is obvious that the clutch plates need to be inspected, for they are most likely worn and/or damaged beyond service limit. this will show more likely in the higher gears.

Mar 24, 2009 | 2006 Vento V Thunder XL

1 Answer

Noisy clutch

I believe they all do that sir. Certainly mine does and has for the 10,000 miles I've put on it.

Nov 10, 2008 | 2005 Triumph Speed Four

Not finding what you are looking for?
2002 Ducati Monster 750 i.e. Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ducati Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers


Level 3 Expert

64052 Answers

Are you a Ducati Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides