Question about 2000 Ducati MH900e
Manufacturer Spark Plug Gap A spark plug part number might fit hundreds of engines and although the factory will typically set a gap to a pre-selected setting this gap may not be optimum for your particular engine and may not take into account modifications that you may have made to the engine. Spark Plug Gap – Bigger is Better The larger the spark kernel that is generated by a spark jumping the electrode gap, the more likely and complete the fuel burn will be, and the smoother the engine will run. That is, the larger the spark gap that’s exposed to the air/fuel mixture, the easier it is to initiate combustion. This translates directly into improved throttle response. So, the larger the plug gap you can run (without misfires) the better. Unfortunately, the greater the plug gap, the higher the voltage requirement to jump the gap. The difficulty lies in that, any added gap creates more strain on the other ignition parts. Coils, for example, may not have enough stored energy to cross the gap, creating a misfire. Old plug wire insulation can break down at the higher voltages required to fire a larger gap. The stock Ducati coils are good enough to fire a 0.044-inch plug gap. Any gap larger than this will likely result in more misfires (there’s always a few) and subsequent power loss. The correct new plug gap is specified at about 0.024-inch (0.6mm). But, remember, as a plug wears, the gap opens up further. If you use conventional sparkplugs, start with the recommended gap and try opening the gap up in 0.002-inch increments. You should note a progressively smoother throttle response if not more power. When the bike begins to lose power, go back 0.001 - 0.002 inch and this will be your optimum gap. I don't know offhand what the DCPR8E plug comes pre-gapped at but as a good rule-of-thumb, if you go more than 0.008 inch over the out-of-the-box gap you won’t maintain parallel surfaces between ground and the center electrodes. So if you reach that point, change to a plug that starts at a larger gap. The NGK dash 9 series starts at a 0.9mm (0.035-inch) gap, and is used for that reason. If you run iridium or platinum electrode plugs, start with the 0.035-inch gap that they are shipped with. Don't run them at smaller gaps or you'll loose throttle response. If you have a older bike, you may arc over the plug wires before you can reach the optimum plug gap. If the spark plug wires have inadequate insulation, the wire cannot maintain a high enough voltage across the insulation and will arc to ground before firing the plug gap. The factory spark plug leads are stranded wire covered with an EPDM jacket and although the wire itself will last a long time, the jacket will start to break down after a couple of years which is why most good aftermarket wire is insulated with silicone rubber. If this is the case, replace the stock spark plug wires with a set of Magnecor or similar quality wires. This will allow running a larger plug gap without a concern for insulating the higher voltage needed to jump the gap. Ducati 916 Magnecor #2549 wires, for example, run $67. Ignition Amplifiers Running a larger gap is the main benefit of installing an ignition amplifier, such as the one sold by Evoluzione for Ducati's. The Evoluzione ignition amplifier increases the primary voltage to the stock Ducati coil from the existing battery voltage to either 16 volt or 18 volt (user selectable). A higher primary voltage means you get a higher secondary voltage applied to the wires and plugs. The higher the secondary voltage - the larger gap it will jump across. Evoluzione recommends that for best throttle response, you run a 0.060 inch plug gap. One reservation that I have about ignition amplifiers as a group is that they could possibly cause overheating and eventual failure of the stock coils or wires. This reliability consideration has to be balanced against improved performance. An independent test by Road Racing World magazine on a GSXR 1000 saw only about a 0.2 HP improvement, but throttle response is the major benefit.,,,
Posted on Nov 10, 2008
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Feb 04, 2016 | 1988 Oldsmobile Cutlass Ciera
Dec 15, 2015 | Cars & Trucks
Sep 22, 2013 | Spark Plugs BR4HS Plug 10/BX #3322
If you're replacing the spark plugs in your car
engine, you'll need to set the gap before reseating the
spark plug. The gap is the distance electricity arcs between the ground
electrode and center electrode. The gap must be set correctly to ensure
maximum performance. Here's how to set the gap of a spark plug.
Dec 10, 2010 | 1997 Pontiac Grand Am
May 02, 2009 | Pontiac Sunfire Cars & Trucks
Nov 10, 2008 | 2008 Buell XB12XT
Nov 10, 2008 | 1999 Bimota SB8R
Nov 10, 2008 | 2005 Benelli Velvet 125
Nov 10, 2008 | 1972 Aermacchi Sprint 350
322 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: