Question about 2000 Ducati 996 Bi~ - Monoposto - SPS

1 Answer

Throttle bodies linkage worn

Hi I have been informed by the Duke mechanic

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

After having the valves done and belts replaced that my Throttle bodies can't be sync'd because of worn linkage see pic. I have looked around and haven't read of this happening often. Sounds like a rare problem. Anyone know of this happening? I can get the linkage rod but where it connects to the butterfly valve is worn or so im told , i get the bike back today and will check it out. If the linkage is stuffed i am thinking 2nd hand Throttle bodies as an option but am not sure about the interchangeability of the 916 748 996 bodies ,the 2nd hand bodies around are mostly 748 916 . Can these be used or am i waiting for a set of 996?,If he can't sync it because the linkage is worn - you need a new tech Ask him, og diy - use only one idle screw - on the TB's where the cable is attached. On the other TB - just remove the screw, and you will be fine After this - the spring will eliminate the slak on the linkage. Sync is a bit different - both airscrews in same position, and adjust the lenght on the linkage to your TB are in sync.,,,

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gm code p2120


Code p2120 is accelerator pedal position sensor APP sensor 1 circuit apparently this is known as the reduced engine power syndrome and is quite common on the avalanche. There is no mechanical linkage from gas pedal to throttle body and it is quite common for the throttle position sensor located on throttle body to mess up and throw this code and also for one of the wires to the throttle position sensor to get hot become brittle and sometimes break. I would start there

Aug 04, 2014 | 2003 Chevrolet Avalanche

1 Answer

How do i replace the throttle body linkage bushing


Follow The Hose From The Air Filter Housing It Goes To The Throttle Body Assembly.... Then Follow The TV Cabe From The Transmission To The Throttle Body Linkage The Grommet Usually Brakes Causing The Transmission Not To Shift Correctly Or Not At All.... The Grommet is Pressed Into The Throttle Body Linkage Pretty Simple Fix!!!!

May 19, 2014 | 1988 Lincoln Town Car

2 Answers

What is the tps sensor


TPS = Throttle Position Sensor. It attaches to side of throttlebody and moves via your throttle shaft, sending information back to computer for proper fuel delivery. If you look on opposite side of throttle body where your throttle cable/linkages are attached, you will find the TPS. Usually held on by 2 screws, and there will be an electrical connector attached.

Oct 19, 2010 | 1984 Toyota Pickup Deluxe

2 Answers

I have code p2176 2004 gmc envoy. is the tps sensor dab?


This code comes up as a safety measure. It is telling you that either the gas pedal is hanging up, struck ect... or the butterfly in the throttle body is hanging up, not returning to center.
Please let me know aht you find.

Feb 12, 2010 | 2004 GMC Envoy

1 Answer

2005 Ford Expedition (4wd) with trouble codes p2104 and p2112 completely cuts off at low speeds. All signs point to throttle position sensor, but want to make sure I'm on the right track.


Shown here is the P2104 obd2 code and their general meaning. For a brief description of any particular OBD2 code and how to fix the obd2 trouble code, please browsw below. P2104 Engine TP Actuator Cntl System
This obd2 code is very common on newer vehicles which contain new design of throttle positioner sensor. Instead of putting a tps sensor at the side of your throttle body as in older engines, a throttle actuator control system is installed which eliminates the mechanical linkage (cable) between the throttle body and the throttle pedal. Under the throttle pedal, a throttle switch is installed and a throttle module or actuator is incorporated beside the throttle body. Because there is no mechanical device that wears out, it is more effecient in delivering better mileage and performance torque (besides...the actuator module performs better in getting all throttle signals to the ecm and trany).
To test this code, check the integrity of the wires going to both the throttle body actuator and the ecm including the throttle switch. Most of the time, if you have symptoms like trany going to a limp mode, the culprit originates from the trany circuit. However, if the symptom is engine related like hesitation, the problem resides in the throttle actuator itself which may sometimes includes the replacement of the whole throttle body assembly. Contact ATS if you need a wiring diagram or detailed fixes for your throttle actuator control system.
TIP:
Before replacing the throttle control actuator and throttle body, try cleaning the throttle plates and all plug-in wiring connections. Also, watch out the throttle body mounting bolts which can easily break (use care) when removing them.

P2112 Throttle Actuator Control System - Stuck Closed

Jan 12, 2010 | 2005 Ford Expedition

3 Answers

Full throttle all the time


We actually have a TSB for the drive by wire systems that calls for both a TPS sensor/actuator replacement but it's required that you also do a PCM reflash at the same time. If you put in the new updated part without doing your reflash then you've found your problem.

Take it to the dealer and get the reflash done.

Nov 23, 2009 | 2004 Hyundai Tiburon

1 Answer

Stop safely now light and Hybrid component failure


There is a technical service bulletin that may apply to your problem the no. is 09-8-9

ISSUE: Some 2005-2009 Escape Hybrid and 2006-2009 Mariner Hybrid vehicles may exhibit an intermittent Red Triangle On and Stop Safely Now message displayed on the message center accompanied by a sudden RPM loss/no start symptom with a diagnostic trouble code (DTC) P1A0C. Vehicles may exhibit this symptom on the first start of the morning or after an extended idle. The symptom will clear on the next key cycle.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE For vehicles outside the new vehicle limited warranty, if diagnostics lead to replacing the throttle body you may use this procedure to clean the throttle body as an alternative to replacing it. This procedure is not covered by the new vehicle limited warranty. NOTE: THIS CLEANING PROCEDURE CAN ONLY BE USED ON NON-COATED THROTTLE BODIES. Refer to Workshop Manual, Section 303-04C Removal and Installation - Throttle Body.
  1. Remove the throttle body.
  2. With the throttle body positioned to the side, open the throttle plate.
  3. Using Motorcraft® Choke and Linkage Cleaner or equivalent, spray the throttle body plate and bore.
  4. Using a suitable (nylon) brush, clean the edges of the throttle plate and the mating surface of the throttle bore to remove all carbon build up.
  5. Reapply Motorcraft® Choke and Linkage Cleaner or equivalent and wipe clean with a lint-free cloth.
  6. Remove old throttle body gasket and discard. Install a new throttle body gasket.
  7. Install the throttle body.

PART NUMBER PART NAME PM-14 Motorcraft® Choke and Linkage Cleaner

Apr 18, 2009 | Mercury Mariner Hybrid Cars & Trucks

2 Answers

2.5l iron duke will not idle


Scan again & check reading of the ECT sensor,coolent sensor as it may be reading to cold for present temp & just dumping fuel as it is seeing -30c all the time.I as well own a iron duke(1987)

Apr 06, 2009 | 1988 Chevrolet S-10

1 Answer

Throttle body linkage worn?


other than to say he couldn't adjust it because one or the other would be off. Does this make sense? If so it appears Ducati doens't sell the the linkage separately only the complete throttle body assemby with a price tag of $2300 (up here). I did find a 2004 999s throttle body assembly on ebay: http://cgi.ebay.com/ebaymotors/DUCAT...3286.m20.l1116 Looks a little different from mine, but I thought the 999 and 998 are supposed to be the same motor. Can anyone tell me with 100% confidence that it will fit an function without significant modification? Or at least if the throttle linkage can be transplanted?,The linkages are different between a 998 and a 999. From what I can remember you can make them fit but with a hell of a lot of mods..... people who have done it may help. Also check out Gotham Cycle breakers in Florida, he had a write up between what models can be transplanted. (Dont have the link sorry) The linkage is worn????? Can you post a picture to show which part he thinks is worn please? By how much will they not sink? Is this on vacuum check or on CO check of each cylinder? Has he done a TPS reset on the setup? Does this guy have a DDS unit? (Basically a hand held computer to check the brains of the bike) Is this being tested with new spark plugs fitted?,,,

Nov 10, 2008 | 2002 Ducati 998 S

1 Answer

Throttle bodies linkage worn


after having the valves done and belts replaced that my Throttle bodies can't be sync'd because of worn linkage see pic. I have looked around and haven't read of this happening often. Sounds like a rare problem. Anyone know of this happening? I can get the linkage rod but where it connects to the butterfly valve is worn or so im told , i get the bike back today and will check it out. If the linkage is stuffed i am thinking 2nd hand Throttle bodies as an option but am not sure about the interchangeability of the 916 748 996 bodies ,the 2nd hand bodies around are mostly 748 916 . Can these be used or am i waiting for a set of 996?,If he can't sync it because the linkage is worn - you need a new tech Ask him, og diy - use only one idle screw - on the TB's where the cable is attached. On the other TB - just remove the screw, and you will be fine After this - the spring will eliminate the slak on the linkage. Sync is a bit different - both airscrews in same position, and adjust the lenght on the linkage to your TB are in sync.,,,

Nov 10, 2008 | 2001 Ducati 996

Not finding what you are looking for?
2000 Ducati 996 Bi~ - Monoposto - SPS Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ducati Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

yadayada
yadayada

Level 3 Expert

67912 Answers

Are you a Ducati Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...