Question about 2004 Bimota 666 L.E.

1 Answer

Revs issues Well now that it is time to sell this piece I get some more problems with it. If you rev the bike a little the revs will just run away. Here's the deal: I have not yet synched the carbs. Timing is dead on and even a little retarde will still run away with the revs With the stock jets the bike just bogs at about 7000 rpms thats why I'm running the slighly smaller ones. So are the revs running because: To lean a mixture?If so then it will run like crumb at top end Incorrect timing? Although it is right on at the timing marks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Could something be wrong? Incorrect point gap? Does this make the revs run away? Carb syncronization? Would this make that big of a difference would I have to change the jets to the bigger one? i am confused! you will have to explain better. if you mean that the engine is reving without the throttle. then forget the whole ignition system for now. it must be getting air/fuel to rev. so check for sticking throttle/linkage or for a vacum leak. when its reving on its own grab the carb linkage and try to return it back. also while its running take the airbox off and shine a light in there and see how far open the throttle plate (s) is.,,

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kawasaki Ninja, ZX6r, 1997 F3. The bike starts great and rev's great when standing. At high rev's its as sweet as a nut. The problem seems to be when riding the bike and the revs are below 4,000....


There are adjustments on carbs for low speed air intake (air mixture screw)find out factory settings and reset that mixture.Sounds to me like those adjustments are out of sink.If so the bike will run very bad from idle to about 1/4 throttle then run great from there up to full throttle.this definitly sounds like carb problem.

Mar 13, 2011 | 1997 kawasaki ZX-6R Ninja

1 Answer

"cold" start issue - engine cranks and revs right


FICV
fast idle control valve
and a price problem
not hard to replace but a $200 part

Dec 08, 2010 | 1991 Honda Accord

1 Answer

Engine misfires around 5000 revs and sometimes


Give your bike a tune up, Plugs , Air filter, clean the carbs. Do these jobs one at a time till the problem goes away, Dirty fuel from leaving the bike unused can also give grief.
Happy hunting

Jun 06, 2010 | 2005 Yamaha FZS 1000 Fazer

1 Answer

VFR400 NC30 - Idle and gear problems


tHE CLUNK YOU TALK ABOUT WILL BE BECAUSE THE REVS ARE TOO HIGH, AS FOR THE HIGH REV'S, COULD BE SOMETHING TO DO WITH THE OTHER GUY HAS NOT ADJUSTED THE THROTTLE MECHANISM PROPERLY

Jan 03, 2010 | 1995 Honda VFR 400 R NC30

1 Answer

When 1973 enduro is in higher gear the bike revs


Yes, it does sound like a clutch, but make sure you have a little free play in the clutch lever. Age will make the clutch plates deteriorate.
You need to remove the right side engine cover to get at it. Take your time and note where all of the pieces are. Pre-soak the new clutch plates (The ones with fiber on them) in oil before you install them.

Dec 26, 2009 | 1974 Yamaha DT 360

1 Answer

Carburetor problem


You must make sure the floats still float and they are set exactly at the factory called for setting.They sound a little low. Also make sure you have no dirt in the needle and seat area. Take a can of carb cleaner and blast it through all fuel passage ways and little holes.Then the same pass. and holes should be blown through with compressed air.
I hope this helps you.

Sep 22, 2009 | Yamaha FZ 600 Motorcycles

2 Answers

Crf 150f backfire


change the jetting...youcan contact FMF for thier setup recommendations for running that pipe with the bike...very common problem and jetting will take care of alot of the issue

Mar 31, 2009 | 2003 Honda CRF 150 F

1 Answer

Rough running kawasaki


you need to let it warm up before beating on it. inline 4s are always cranky when cold. another issue could be dirty carbs and clogged carb jets causeing it to run extreemly lean, rev high and die out. pulling 4 carbs isnt "fun" but you could do it in an afternoon.

Mar 07, 2009 | 1995 kawasaki ZX-6R Ninja

1 Answer

Et2 Cutting out and not maintaining revs


There is an adjustment screw on the carburetor facing towards the back wheel. You have to reach down about finger length. With the engine running and the ET2 on its stand, turn the screw until the engine revs up to a level you r happy with.

Happy scooting

Jan 26, 2009 | Peg Perego Vespa Scooter

Not finding what you are looking for?
2004 Bimota 666 L.E. Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bimota Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

69199 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Bimota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...