Question about 2005 Beta Alp 200

1 Answer

Delay gas power

When I give my motoryclce gas

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

It takes it a sec or two for the engine to respond. For instance if I'm in neutral and all of a sudden I give it some gas for about a second it'll be like I haven't touched it, stays the same sound and all, and then revs up. It's like it's delayed or something. This happens on and off with it.,Stabbing in the dark...... jetting too rich(pilot jets)?, choke sticking?, air screws out of adjustment? carbs out of balance? time warp messing with your perception?,,,

Posted on Nov 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kozy world wall heater makes a boom pop when it lites. It's like a delay in lighting and then it lites.


If the furnace made a clicking noise trying to turn on and then makes the BANG noise at the furnace, it’s most likely a delayed ignition. Imagine a room full of gas and then someone decides to light a match. Big problem. That's what’s happening in your furnace if the ignition of gas is delayed.

A variety of issues can delay the combustion of that gas. So the gas builds up in the furnace until—BOOM—it ignites, causing a mini-explosion. This can harm the heat exchanger, which is very expensive part to replace. Some causes of delayed ignition includes:

1. Dirty burners
2. Flames are lifting away from the burner outlet due to too much primary air
3. Too much gas

If you're handy enough to understand what I've said then burners can be cleaned/replaced, and primary air can be adjusted. With some units gas flow can be adjusted as well; other times the gas valve will need to be replaced.

If you've no idea what I've described, GET HELP before you ruin the heat exchanger and have a more expensive problem on your hands or worse...

Dec 24, 2016 | World Heating & Cooling

1 Answer

Delayed Power Up


Probable regulated 12v power supply.....To help further....need
info....Model # and service # and mo /yr built off back of set..T.

Dec 21, 2007 | Televison & Video

1 Answer

My kozy world wall heater makes a boom pop when it lites


If the furnace made a clicking noise trying to turn on and then makes the BANG noise at the furnace, it’s most likely a delayed ignition. Imagine a room full of gas and then someone decides to light a match. Big problem. That's what’s happening in your furnace if the ignition of gas is delayed.

A variety of issues can delay the combustion of that gas. So the gas builds up in the furnace until—BOOM—it ignites, causing a mini-explosion. This can harm the heat exchanger, which is very expensive part to replace. Some causes of delayed ignition includes:

1. Dirty burners
2. Flames are lifting away from the burner outlet due to too much primary air
3. Too much gas

If you're handy enough to understand what I've said then burners can be cleaned/replaced, and primary air can be adjusted. With some units gas flow can be adjusted as well; other times the gas valve will need to be replaced.

If you've no idea what I've described, GET HELP before you ruin the heat exchanger and have a more expensive problem on your hands or worse...

Dec 24, 2016 | World Heating & Cooling

1 Answer

Takes a while to ignite and when it does the build up of gas causes an explosion that is increasing in size each time I turn it in both oven and range


PDF]Gas Range Delayed Ignitions - Consumer Product Safety ...

https://www.cpsc.gov/.../Kitc... U.S. Consumer Product Safety CommissionJul 15, 2002 - Investigation of Delayed-Ignition Range and Igniter Aging . ... and ovenexplosions and flare-ups attributable to delayed ignition of gas.

Jul 19, 2015 | Kitchen Ranges

1 Answer

2009 mini cooper clubman with sport button-delay when press on gas.


The fuel pressure and fuel system needs to be inspected.
-------
I suggest you few helk links.Click the link below and follow its troubleshooting procedure:------------------Pushing on the gas pedal, but the car slows down? Gas pedal to the floor and the car slows down? http://technoanswers.blogspot.in/2012/02/pushing-on-gas-pedal-but-car-slows-down.html
-------------
Car dies when gas pedal is pressed? http://schematicsdiagram.blogspot.com/2011/12/car-dies-when-gas-pedal-is-pressed.html
---------------
Car won't start without hitting the gas pedal? http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-without-hitting-gas.html
-------------Car only starts when gas pedal is pressed? http://technoanswers.blogspot.com/2012/01/car-only-starts-when-gas-pedal-is.html
----------1999 Ford F-150 Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html
----------Delay starting on Toyota Prius? http://schematicsdiagram.blogspot.in/2012/02/delay-starting-on-toyota-prius.html

--------
These will help.
Thanks.

Nov 26, 2012 | Cars & Trucks

1 Answer

How can I get an Immediate output from universal remote receiver without 3minute delay,as a temperature control output for the compressor?Can anyone give me response. thnks.


The three minute delay is there to protect the compressor from pressure overload. Otherwise it would burn out.
When a compressor is running it is pumping against high pressure. When you shut it off, then instantly turn it back on, the head pressure of the refrigerant gas is too much for it to restart against. So the delay allows the pressure to equalize between the suction and pressure sides making it much easier to start. Otherwise you would need a larger compressor and it would burn too much electricity.
Hope this helps,
Best,
Mark

Dec 28, 2010 | Heating & Cooling

1 Answer

What are the carrier 8000ts led error codes?


They are listed inside the front panel of the main unit.

LED CODE

EACH OF THE FOLLOWING STATUS CODES IS A TWO DIGIT NUMBER WITH THE FIRST

DIGIT DETERMINED BY THE NUMBER OF SHORT FLASHES AND THE SECOND DIGIT BY

THE NUMBER OF LONG FLASHES.

STATUS

11 NO PREVIOUS CODE - Stored status code is erased automatically after 72

hours. On RED LED boards stored status codes can also be erased when power

(115 VAC or 24 VAC) to control is interrupted.

12 BLOWER ON AFTER POWER UP (115 VAC or 24 VAC) -Blower runs for 90

seconds, if unit is powered up during a call for heat (R-W closed) or R-W opens

during blower on-delay.

13 LIMIT CIRCUIT LOCKOUT - Lockout occurs if the limit or flame rollout switch is

open longer than 3 minutes.

- Control will auto reset after three hours. - Refer to #33.

14 IGNITION LOCKOUT - Control will auto-reset after three hours. Refer to #34.

21 GAS HEATING LOCKOUT - Control will NOT auto reset.

Check for: - Mis-wired gas valve -Defective control (valve relay)

22 ABNORMAL FLAME-PROVING SIGNAL - Flame is proved while gas valve is

de-energized. Inducer will run until fault is cleared. Check for:

- Leaky gas valve - Stuck-open gas valve

23 PRESSURE SWITCH DID NOT OPEN Check for:

- Obstructed pressure tubing. - Pressure switch stuck closed.

24 SECONDARY VOLTAGE FUSE IS OPEN Check for:

- Short circuit in secondary voltage (24VAC) wiring.

31 PRESSURE SWITCH DID NOT CLOSE OR REOPENED - If open longer than

five minutes, inducer shuts off for 15 minutes before retry. Check for:

- Excessive wind - Proper vent sizing - Defective inducer motor

- Low inducer voltage (115VAC) - Defective pressure switch

- Inadequate combustion air supply - Restricted vent

- Disconnected or obstructed pressure tubing

- Low inlet gas pressure (if LGPS used)

If it opens during blower on-delay period, blower will come on for the selected

blower off-delay.

33 LIMIT CIRCUIT FAULT - Indicates a limit, or flame rollout is open. Blower will

run for 4 minutes or until open switch remakes whichever is longer. If open

longer than 3 minutes, code changes to lockout #13. If open less than 3 minutes

status code #33 continues to flash until blower shuts off. Flame rollout switch

requires manual reset. Check for: - Restricted vent

- Proper vent sizing - Loose blower wheel - Excessive wind

- Dirty filter or restricted duct system.

- Defective blower motor or capacitor. - Defective switch or connections.

- Inadequate combustion air supply (Flame Roll-out Switch open).

34 IGNITION PROVING FAILURE - Control will try three more times before lockout

#14 occurs. If flame signal lost during blower on-delay period, blower will come

on for the selected blower off-delay. Check for: - Control ground continuity

- Flame sensor must not be grounded

- Oxide buildup on flame sensor (clean with fine steel wool).

- Proper flame sense microamps (.5 microamps D.C. min., 4.0 - 6.0 nominal).

- Gas valve defective or gas valve turned off - Manual valve shut-off

- Defective Hot Surface Ignitor

- Low inlet gas pressure

- Inadequate flame carryover or rough ignition

- Green/Yellow wire MUST be connected to furnace sheet metal

45 CONTROL CIRCUITRY LOCKOUT Auto-reset after one hour lockout due to;

- Gas valve relay stuck open - Flame sense circuit failure

- Software check error

Reset power to clear lockout. Replace control if status code repeats.

If status code recall is needed, briefly remove then reconnect one main limit wire to display

stored status code. On RED LED boards do not remove power or blower door before initiating

status code recall. After one status code recall is completed component test will occur.


Thanks for Choosing FixYa.


Kelly

Oct 05, 2010 | Heating & Cooling

1 Answer

I have a TH8000 Vision Pro. It is controling a


Whats' so hard is the Honeywell thermostat has a built in 1@ differential. It is not adjustable.
You might ask your installer about a time delay relay installed in the furnace to break the thermostat heat wire (usually white wire).
Most time delay relays are 90 seconds. But that might be enough to reduce the furnace cycling.

Dec 15, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

Bryant programmable thermostat will switch on furnace


Turn the power off to the Air handler unit.
Remove the thermostat from the wall, (Just the face part).
Look on the back side of the thermostat and verify that the jumpers are set to electric and not gas, otherwise the fan will not run during heat mode, they come from the factory usually set for gas.
If this is a electric heater this will solve your problem, If it is gas then it will be more detailed. Once you put it back on keep in mind that most thermostats have a 3-5 minute delay so just give it a little time and the fan should then work once you have the jumpers in the correct position.

FlaTech
Thank you for using FixYa!

Nov 17, 2009 | Bryant Heating & Cooling

Not finding what you are looking for?
2005 Beta Alp 200 Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Beta Experts

Mark Schmit
Mark Schmit

Level 3 Expert

1915 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

37981 Answers

Damian Appert
Damian Appert

Level 2 Expert

112 Answers

Are you a Beta Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...