Question about 2008 Benelli Tornado Tre 1130

1 Answer

Turn sighn not blinking

It did this while i was tryin to figure how to wire the signals on. the back will go on but not blink. it does not blink on the controls either. i checked the connections and they are solid. could the bulb just be dead?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Make sure that both the front and the rear lites are burning on the brightest filament. And that you have a good ground. The rear lite only works for a signal in most cases the front has two filaments one for running lite the other for turn signal. The brightest are for turning signals. Good luck.,

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where's the flasher on a 1993 Suzuki Intruder VS 1400?


replace the indicater relay ! trace back the same colour wires !

Apr 04, 2014 | 1993 Suzuki VS 1400 Intruder

1 Answer

Suzuki boulevard s50


if the filiments are still intact and not blown in the bulb and the rear still works you probably have a rubbed wire rom the bulb to the blinker relay.

Jul 11, 2013 | Motorcycles

1 Answer

2005 harley rr turn signal only works with brake applied


Hi Anonymous, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics

Sep 10, 2012 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Front left running light burns too bright and left rear blinker blinks faster.


Hi Kevin, you have the front left turn signal bulb installed 180 degrees out or your wiring is bass ackwards. Good luck and have nice day.

Mar 10, 2012 | 2008 Harley Davidson FLSTC Heritage...

1 Answer

Just bot 1982 gpz750n0 volts to my back signal lights front signal they come on but dont blink fuses ok


Separate problems.
0 volts = bad connection. Follow the wires till you find the break - or corroded - wire/connector and fix it.
no blinking = the signal relay has died, replace it.

Oct 04, 2011 | 1992 kawasaki GT 750

3 Answers

My back lights went out they blink but that's it the front are on and blink the back just blink


This is going to be a problem with a loose connection. Loose connections are usually pretty easy to find. Anywhere you can see wire, wiggle it. And see if the lights stay on or go off. Just looking for a change.

Oct 20, 2010 | 1996 kawasaki VN 800 Vulcan Classic

1 Answer

My right turn signal blinks really fast & the same running light on the front is brighter than the left turn signal


One light is brighter because the turn signal light wire is switched with the running light wire. The wires are color coded should be an easy fix. As for the fast blink, if you have put led lights on the signals you will have to also add a diodes to correct the fast blink.

Jun 24, 2010 | 2004 Honda VTX 1300

1 Answer

Wire loose


The blue wire is the wire to supply voltage to your "running" lamp filament in the buld. Take your bulb out and look at the back side of it. It should have two round connectors on it. One is for the turn signal and one is for the running light. The "running light" should be on when you start the bike. When you turn the turn signal on on that side, the turn signsl filament should light up along with the running light filament.

With the bike running and headlight on, all four turn signals should lit as "running lights". Earlier models did not have the "running lights' on them. Now, when you turn the turn signals on either side the bulbs should blink much brighter. If you press and hold both the right and left turn signal switches, you're four way flasher signal should come on. If you still can't figure it out, Drop me a line at wd4ity@bellsouth.net and I will scan a wiring diagram in for you and send it to you. Good Luck Steve

Apr 25, 2010 | 2000 Harley Davidson XL Sportster 883

1 Answer

Signal lights on R1 don't work...


Though I can't recall what the wire colors are for your bike's turn signals, here's how to figure it out: on the turn signals that you bought, first determine which wire is the ground by removing the light bulb and then checking to see which wire has continuity to the turn signal's metal bulb socket base.
Then find out which wire is the running light and which is the turn signal by hooking the ground wire and one of the other wires to a 12 volt power source. Which ever wire makes the brighter part of the bulb light up is the turn signal - the dimmer one is for the running light.
On the bike, match the turn signal wire to the bike's wiring that is 'hot' with the turn signal switch on. Plug the running light wire from the turn signal into the bike's wiring that is 'hot' whever the key is on. Hook the turn signal ground wire to the bike's ground wire(s).

Dec 03, 2009 | 2001 Yamaha YZF-R1

Not finding what you are looking for?
2008 Benelli Tornado Tre 1130 Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Benelli Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Connie Richardson

Level 1 Expert

15 Answers

Jazz Boyce
Jazz Boyce

Level 1 Expert

728 Answers

Are you a Benelli Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...