Question about 2007 AJP PR4 125 Enduro

2 Answers

Re jet the carburetors

What does it mean to “re-jet” the carburetors?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

The November 10, 2008 solution is correct but a bit more should be added. > > Forget modifing the jets. The effort will be a waste at best. Instead, just go to the dealer and tell him the problem. Jets are a VERY low cost item. If in a high altitude state like Colorado a smaller jet may be needed since less oxygen requires a thinner fuel mix. If at sea level, a larger jet may be appropriate. The only jet needing replaced at any time is the main jet. The needle jet is a variable flow jet and the flow is controlled by the throttle.

Posted on Mar 11, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Carburetors supply a mixture of gasoline and air to the engine. The gas comes out of little things called “jets” (usually a pilot jet needle jet and main jet). If you modify your airbox or exhaust to flow more freely you get more air going through your system. This often means that there is not enough gasoline so the engine runs badly. “Rejetting” means replacing or modifying some of these jets so as to supply gasoline differently than stock, usually more gasoline than stock. If done correctly, this allows your engine to generate more power, run a little cooler, start and run smoother and get worse mileage. ,,,

Posted on Nov 10, 2008

1 Suggested Answer

  • 2336 Answers

SOURCE: carburetors

Carburetors supply a mixture of gasoline and air to the engine. The gas comes out of little things called “jets” (usually a pilot jet, needle jet and main jet). If you modify your airbox or exhaust to flow more freely, you get more air going through your system. This often means that there is not enough gasoline, so the engine runs badly. “Rejetting” means replacing or modifying some of these jets so as to supply gasoline differently than stock, usually more gasoline than stock. If done correctly, this allows your engine to generate more power, run a little cooler, start and run smoother and get worse mileage.

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i lower the throttle pin on 2001 ktm 300 exc


if you need you bike jetted for 7000, take it to a shop and have it jetted.
If you dont understand your carburetor and make the wrong adjustment you can lean out and blow up the engine.
when you jet a bike for 7000, you need to change everything, main jet, idle jet, idle mixture, idle, and needle position.

Apr 15, 2013 | 2001 KTM EXC 300

1 Answer

Will not idle and bogy off the line


Instructions
    • 1 Turn the gas valve between the gas tank and the carburetor to the off position. Place the drain container under the nut on the bottom of the carburetor.
    • 2 Remove the nut on the bottom of the carburetor with the pliers. Drain the gas into the container and then replace and tighten the nut.
    • 3 Remove the stock jets from the right and left side of the carburetor with the screwdriver. The jets are the gold pins that are in clear view.
    • 4 Insert the new jet pins into the jet holes according to the instructions in the jet package. Tighten the jets according to the jet chart in the rear of the owner's manual.

Jan 20, 2013 | Honda CR 125 R Motorcycles

1 Answer

Wont start


Instructions
    • 1 Remove the seat by unscrewing the bolts found on the four corners of the seat. Remove the clamps from the top of the air box using a pair of pliers to access and remove the air filter. The air filter is removed by unscrewing the wing nut and sliding the filter out of the box. Loosen the hose clamp that connects the carburetor to the intake manifold, using a screwdriver.
    • 2 Loosen the fuel delivery hose clamp with a screwdriver and pull the carburetor out of the Blaster. Before troubleshooting the carburetor, it's important to note whether you've made a significant change in altitude or a change in your exhaust/intake setup. If you've made an altitude change, installed an aftermarket exhaust pipe or modified your air box, the jets will need to be changed. Refer to your manual for specific re-jetting instructions based on your altitude. Your exhaust kit will provide a recommended jetting setup. Do-it-yourself modifications like removing an air box will require you to experiment with the jet setup until you find the right one.
    • 3 Disassemble the carburetor by unscrewing the bowl screws from the bottom of the carburetor. With the bowl removed, the float, pilot jet and main jet will be exposed. To remove the pilot and main jet, unscrew them from their respective holes. The main jet will sit in the exact center of the bowl, while the smaller pilot jet will be set just below the main jet.
      Use a blunt object like a stick or rod to push the bottom of the needle receiver assembly out of the carburetor. The needle receiver (which houses the needle jet) will slide out of the top of the carburetor along with the slide, spring, carburetor cap and gasket. The carburetor is now completely disassembled and ready to be inspected.
    • 4 Inspect the pilot jet for blockage, slide a thin wire through the pilot jet's hole, spray it with carburetor spray and blow the center hole with compressed air. Repeat this process with the main jet. If there is any blockage or wear, replace the jets. If you have made altitude changes or exhaust/intake modifications, insert jets that correspond to your changes as recommended in your manual. Note that this may take some experimentation with different jets to get the correct jet setup, as there are many jet sizes for different scenarios.
    • 5 Inspect the bowl, floats and ports for any signs of debris or gunk. If debris or gunk is found, remove it using a spray carburetor cleaner, soft wire brush, or thin wire (to insert into small orifices). If no gunk or debris is found, you've ruled this out as a possible cause for the starting issues, and can focus on the replacement of carburetor components.
    • 6 Look for abnormal wearing on the jets, float valve, gaskets, O-rings and springs. If you have not changed altitude or modified your bike in any way, then it is best to inspect these components. Any one of these components, or a combination, may be contributing to your starting issues. You may choose to replace individual parts such as a new float valve, though replacing all the interior components with a carburetor "rebuild kit" is advised. Rebuild kits can be ordered online or through your dealer, and will ensure your carburetor is fully repaired.
    • 7 Slide the gasket, spring, spring holder and needle jet assembly back onto the carburetor cap and insert the assembly into the top of the carburetor. Screw the main jet into the bottom of the needle jet assembly by accessing it through the bowl area. Screw the pilot jet back into its hole below the main jet. Clip the float valve onto its hinge within the bowl a insert the bowl gasket. Screw the bowl to the bottom of the carburetor to complete the re-assembly process.
    • 8 Re-attach the carburetor to the intake manifold using the hose clamp and screwdriver. Slide the fuel feeder line onto the brass receiver port on the side of the carburetor and slide the air box boot over the carburetor's intake port, which should be facing toward the back of the bike. Re-install the air filter with its wing nut, slide the clips over the air box top to secure it to the box and slide the seat into place. Re-install the seat screws to complete the re-assembly process.
    • 9 Prime the carburetor by twisting the throttle once and start the Blaster.

Jan 14, 2013 | Yamaha V Star 1100 Custom Motorcycles

2 Answers

How to tune Bajaj Platina's carburetor for good mileage?


check out the carburetor settings and tune it for more air flow ratio from a ecperienced mechanic

Sep 03, 2012 | 2007 Bajaj Platina

1 Answer

I just rejetted ( at least I think I did ) my carburetor on my vstar 1100 custom. The problem is that the Cobra Carb Jet Kit 92-2170 only had main jets.... five of them. Does this mean that only the main...


In many case when you rejet your carburetors you are only changing the mains and the needles(to get rid of the acceleration bog) If they give you several size jets to try, be sure you are putting the right sizes in the right spots. Yamaha typically will run one carburetor leaner than the other. Depending on how the cycle is running , I have known people to match the jets in both carburetors. Check the color of your plugs to double check if you have set the cycle up correctly.

Oct 10, 2010 | 1999 Yamaha V Star 1100 Custom

1 Answer

1985 yamaha maxim 700, Runs good through first half of throttle but when you try to get past that it just boggs down. Carbs have been cleaned. Spark plugs are jet black after a quick ride? Any help is...


Hello, from your description, it sounds like some of the jets of your carburetors are in the wrong places. Your bike has four carburetors, and each one of them has a main fuel jet and an idle fuel jet inside the bowl. The main jet goes in the very middle of the bowl and is the one that screws into the needle jet. This main jet has a relatively large hole through the middle. The pilot jet goes off to the side of, and screws right into the metal of the carburetor body. This jet has a very small hole through the middle -- so small that it may be hard to see through it.

These two jets look similar at a glance, and they have identical threads which makes it easy to get them in the wrong place. You mention that your carburetors have been cleaned, so there is a good chance that whoever cleaned them accidentally switched these jets in some or all of your carburetors.

If these jets are switched you will notice the following symptoms:
  1. Your bike will start very easily with little or no choke even when it has not been run for a while.
  2. Your spark plug electrodes will be very dark black after even a little running.
  3. It will feel like you have little power from the middle of the throttle all the way to wide open throttle (WOT).
  4. If you run like this for a while you will start to get backfiring, and the bike will start to run on three and then two cylinders, and perhaps eventually not at all.
But don't worry, fixing this problem is easy. It will be especially easy if you are the one who switched the jets in the first place. You just have to take your carburetor rack off of the bike, and remove the four bowls from the bottom. Look at the main and pilot jets in each of the four carburetors. The main jet should have a biiger hole and will have a tiny stamped number that should be around 120 or 130 on the top. The idle jet should have a small hole and a tiny stamped number around 15 or 20 in the top. Be sure that the jets are in the right places, and put your carburetors back together. It is also a good idea to get new spark plugs after you correct the problems, or thoroughly clean your old ones as carbon buildup on the spark plugs may cause a weak spark.

In the attached picture the main jet is toward the bottom, and the idle jet is on the top.
joshorndorff_0.jpg

Good Luck,
-Josh

Aug 27, 2010 | 1985 Yamaha XJ 700 X Maxim

2 Answers

98 honda magna. had fuel stabilizer last october. now it starts with choke but won't rev or idle. only choke keep it running. switched out fuel. put new fuel and additives, but nothing good yet. what...


Even though you put stabilizer in the fuel, it sounds like the jets in the carburetors gummed up. Additives wont do much good at this point. You need to remove, disassemble and clean the carburetor passages and jets.

Jun 25, 2010 | 1998 Honda VF 750 C Magna

3 Answers

The motor dies when i take off the choke


More than likelt it's a dirty carburetor, pilot jet/main jet. Pull off the carb bowl and blow out the the jet with compressed air and try that first.

Feb 21, 2010 | 2001 Yamaha TW 200

3 Answers

I can't get my 2007 virago 250 to start. If I spray starter fluid in the air intake, it starts. If I pull off the hose leading into the carburetor, fuel squirts out when I try and start it. When I...


It sounds like you have a plugged jet or needle in your carb. It will start with a spray, and turning it over sends fuel out of the line means the fuel pump is working. Go over the main jet, needle jet and float needle closely, not to miss any small openings that may be plugged.

Jul 08, 2009 | Yamaha Gladiator SS Motorcycles

1 Answer

Carburetors


Carburetors supply a mixture of gasoline and air to the engine. The gas comes out of little things called “jets” (usually a pilot jet, needle jet and main jet). If you modify your airbox or exhaust to flow more freely, you get more air going through your system. This often means that there is not enough gasoline, so the engine runs badly. “Rejetting” means replacing or modifying some of these jets so as to supply gasoline differently than stock, usually more gasoline than stock. If done correctly, this allows your engine to generate more power, run a little cooler, start and run smoother and get worse mileage.

Nov 20, 2008 | 2004 Harley Davidson VRSCA V-Rod

Not finding what you are looking for?
2007 AJP PR4 125 Enduro Logo

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top AJP Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4471 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Angelo Stewart
Angelo Stewart

Level 2 Expert

224 Answers

Are you an AJP Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...