Question about Hyosung GT 250 Motorcycles

Open Question

Kickstand sensor My kickstand sensor is busted how do bridge or remove it ???

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: Problems with the kickstand and neutral light on 2002 Shadow 600

The side stand kill switch is supposed to kill the engine any time the kickstand is down. This way there is no way you can take out with the stand down > Safety issue. The neutral light could be burned out. fuse burned, bad switch. The switch is located in the center of the front sprocket. There is a 15amp fuse that protects the oil, neutral, meter and tail lights > Is the fuse good?

Go to this site and you can download a free PDF service manual. There is a service manual with a wiring diagram in the back. The manual is for a 2001 VT600 but only minor differences to the 2002 manual.

Top rating on this solution? Thanks :D

Posted on Jun 03, 2009

  • 13 Answers

SOURCE: how do you install a kickstand spring on an 07

hook the front part of the spring on the frame first. Have someone to hold your bike while you lay down and pull the spring to the kickstand. I use vise grips to do this

Posted on Oct 09, 2009

  • 14 Answers

SOURCE: kickstand spring came off


Posted on Oct 31, 2009

  • 51 Answers

SOURCE: kickstand spring popped off, kickstand is now

The kickstand has some kind of safety switch, if the spring is not broke you should be able to snap it back on (with the kickstand up) and have someone to hold the bike or put it on a lift. It might take some muscle or take it to a dealer and I'm sure they can pop it back on. Hope this helps.

Posted on Nov 02, 2009

  • 1 Answer

SOURCE: 04 fxsti 88b motor check oil while bike is on

You need to check oil while bike is upright on a level surface. I believe from 05' and earlier the MOCO designed their softail dip sticks to read the level while the bike is on the jiffy stand.

If oil is hot,it should be at the full mark. If checking cold, it is about 1/4 inch below the full mark.

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can i use brake spring pliers to replace the kickstand spring

Remove the pivot bolt in the kick stand, put the spring on the kickstand and then pull the kickstand into place and get someone to push the pivot bolt back into place.

Aug 12, 2015 | Motorcycles

1 Answer

Hi mate my hyosung gt250r started randomly stalling while I was ridding, thought it was the kickstand cable, yesterday I went to start it started fine but cut off when I put it in gear, Anny ideas why

It does sound like a kickstand sensor issue, as the sensor only works when the bike is in gear. To check, you can bypass the sensor by disconnecting it's cable and then joining the two wires together so there's a permanent electrical connection. If that solves the problem, you need a new kickstand sensor.

May 12, 2015 | Hyosung Motorcycles

1 Answer

I 94 Kawasaki ninja ZX 900 B has a Suzuki motor in it with numbers 3713B3048 Motor dies when you put it into gear to take off

I'd deffinatly say that's the kickstand sensor if it's faulty the bike starts fine and revs but as soon as you go to drive it dies, the bike thinks the kickstand is still down look around the kickstand for wires when you find them disconnect em and try that

Oct 12, 2014 | Motorcycles

1 Answer

Removing a kick Stan on a Harley a 1990

Jack bike so it won't fall over when the kickstand is removed.

Move kickstand half-way between extended (down) and retracted (up).

Remove pivot bolt nut, washer.

Remove pivot bolt.

Unhook kickstand spring.

Mar 01, 2014 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to install an extended kick stand for 2002 heritage softtail classic

Jack up bike to support it.
Undo bolt on top of kickstand, remove.
Remove kickstand stop, unhook spring, slide down and out.

Reverse to install new kickstand.

Apr 17, 2013 | Harley Davidson Motorcycles

1 Answer

I have a 95 CBR600f3 that won't start while the kickstand is down. Is this normal or is there a sensor that may have gone out?

Thgis is normal ... it is a safety interlock. Put the side stand in the storage position before you start and you will be just fine.

Dec 08, 2012 | Motorcycles

1 Answer

Suzuki dr350 is cutting out after engaging gear

could be a clutch issue but first make sure it doesnt have a saftey switch in the kickstand it will be like a secondary kill switch that kills the engine so you don't ride of with the kickstand down its a little sensor that usuall has 2 wires coming out of it sometimes you can bypass it although i dont recommend this as a permanent fix, look near the kickstand pivot for this sensor

Oct 16, 2012 | 1996 Suzuki VS 800 Intruder

1 Answer

Dies when i put it in first

Kickstand sensor is not sensing the kickstand in the up position...take a look at how it works underneath the bike and try to see where the connection is, if when you put the kickstand up and its not touching anything or moving a switch then either the switch is missing or its not in the right place

Aug 29, 2012 | 2000 Yamaha YZF-R1

3 Answers

Bike runs ticks over in neutral soon as iput in gear cuts out

hi...put kickstand up 1st befor putting in this how bigger hondas work its a safety thing so u carnt ride off with side stand down...but cuts engine if kickstand still down & then wont start as you in gear.....even if kickstand up wont start in gear!!...hope this helps

Jan 26, 2010 | Honda XL 125 R Motorcycles

1 Answer

How to put spring back on kickstand 2004 1200 sportster

There is a place on the frame and a place on the kickstand for each end of the spring to connect to. With the bike on the kickstand and someone to help steady the bike, use a pair of side cut pliers or a very strong spring hook to pull the spring and rconnect it to the kickstand.

If you can't get it this way, remove the pivot bolt, connect both ends in their proper positions and work the kickstand back into position so the pivot bolt will go back in.

It's tough but it can be done.

Sep 24, 2009 | 2004 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides