Question about 2003 Yamaha YZ 125

1 Answer

How do i change front wheel berrings

Front wheel is wobboly

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 53 Answers

Those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

tablette pc
lecteur ebook

Posted on Feb 21, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do the front ball bearings have grease fittings for a 2005 Toyota Tacoma prerunner SR5?


if your talking wheel bearings then no these are supposed to be a sealed greased bearing from the factory and not grease able.

Aug 28, 2014 | Cars & Trucks

3 Answers

My 2003 bmw x5 steering wheel vibrates for a couple seconds when I am slowing down and then goes away, do I need new routers?


168c87e9-bd9d-4dc3-9a05-885f92df381e.jpg
Hi there, provided your tyres have been fitted correctly, like others have said there are a few reasons why you can experience what we call a shudder through the steering under braking and what normally feels worse when braking from 100kph/60mph rather then from 50kph/30mph, if you do have warped front discs/rotors they will need to be checked but a common cause for steering shudder also along side warped brake discs are the control arm bushes which is item #7 in the pic supplied and they fit into item #6, these can be seen quite easily with the front of the vehicle jacked up it is the lower control arm seen going from the bottom of the front wheel suspension assembly to forward of the front wheel to cross member/ sub frame, with the vehicle jacked you can see the rubber inside the bush itself to see whether it's cracked, be sure that when they are being replaced as is with all suspension bushes the vehicle must be rested back on its wheels before tightening the bolt item #8 as this is the normal working position of the bush and not in the jacked up position.

Jul 26, 2014 | 2003 BMW X5

1 Answer

Low grinding noise from front axle when stopping my 86 Chevy k5 blazer


Check your wheel berrings by jacking up the frount of the car up until the wheels are off of the ground and then see if the tire wiggles around if it does the berring is shot if the tire is solid then the berring should be fine

Jun 04, 2012 | Chevrolet Blazer Cars & Trucks

2 Answers

Poping,slipping noise,when you excerate fast.Sound come s from front driver side axle.


Most likely the cv joints, Its cheeper to change the axel out........If not that could be the wheel hub berrings,,,,,,,,,,,,,,,,,good luck

Feb 15, 2011 | 1998 Ford Taurus

1 Answer

I need to know exactly how to go about replacing the wheel bearings in my '98 ram 1500 5.2L 2wheel drive...and if it is possible to replace the whole hub... thank you


You forgot to state front or rear, take off the tire remove the grease cap with plyers remove cotter pin remove nut, remove washer, wiggle the hub and outer berring will fall out. The inner berring may be pressed into the back of the hub. If so you will have to knock it out with a hammer. Getting it back in could be difficult. It can also be hammered back in. ( the new berrings must be repacked with grease by you) This is a process whereas you force grease into the berring. The install the hub install the outer berring put on washer tighten nut with plyers then back off 1/8 turn. install pin install cap install tire. after 50 miles of driving lift car and wiggle tire with hands to feel for any play in the berring....because this is your first time!

Sep 09, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

1992 Dodge Pickup d150 1/2 ton need to know the torque for the front wheel bearings. Thank you


after packing your berrings tighten the nut untell the wheel stops turning , then back the nut off 1 flat ( the nut has 6 flat) wheel should now turn with minamal drag

May 20, 2010 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

1998 Windstar: 1998 windstar replaced rotors but steering still s...


make sure the wheel hub surfaces are clean and free of rust both in front of and behind the rotors. also check that your rear brake adjusters are working correctly. also check wheel berring, balljoint and tierod ends for play. theres should be no play and berring should spin free of noise.

May 18, 2010 | 1998 Ford Windstar

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

1 Answer

Need to change front rotors


the larger bearing goes on first pointing towards you as you install it then the rotor goes on the the smaller bearing goes on with it pointing away from you like this > < please rate this. thanks

Oct 01, 2008 | 2003 Ford F150 Regular Cab

3 Answers

Front end


bad tire or outof balance wheel

May 28, 2008 | 2000 Oldsmobile Bravada

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...