Question about 1996 Suzuki VS 1400 Intruder

Open Question

Need a brake master cylinder 1996 suzuiki intruder 1400

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: How do you sync the carbs on a 1996 1400 intruder? John

Hi Lundar,
How many carburtors does yr bike have?
Let me explain you as to how it is done in a Yamaha Seca XJ750A.
I have four carburators in my bike and the # 3 is factory set so all one has to do is set the rest to the # 3.You have to fully open the idling screw thn use a feeler gauge 0.15mm feel it to the # 3 nd thn adjust the rest to let the feeler blade 0.15mm to pass under the butterfly of the rest of the carburators.
Hope this answers yr question!
Visit this site we also have a column for other models prolly you may get someone there who has the same type of bike as yours!..www.xjbikes.com
Knight ( Yamaha Seca XJ750A 1981)

Posted on Feb 10, 2009

Ad
  • 2 Answers

SOURCE: Clutch bleed on a Suzuki 1400 Intruder 2000

One the left-hand side of the bike (facing forward), there is cover plate just ahead of the drive shaft. Remove that cover (mine has 8mm bolts). The bleeder valve is under this cover. Go to an auto parts store and get a "one man bleeder kit" or if you have some plastic tubing that will fit over the valve, you can use that and a clean jar. Follow the instructions on the bleeder kit, or if you're using the jar and tubing, fill the jar about a quarter of the way with break fluid (use DOT4, but never DOT5!). Take the cover off the master cylinder up at the handlebars, place the tube over the end of the bleed valve (after loosening it a turn or two. Place the other end of the tube down in the break fluid in the jar. Work the clutch lever until you stop getting bubbles in the jar. Be sure to keep the fluid level up in the reservoir. Tighten the bleeder valve, remove the tubing, top off the fluid and replace the covers.

Be careful not to get brake fluid on anything. It will eat paint and mess up other things.

Posted on Feb 13, 2009

  • 3567 Answers

SOURCE: shifting problem 96 1400 Intruder 4 speed

Yes, the bad news is bent shift forks. The engine comes out and dissassembles into about 75 different parts. The gears come out, the the shift drum, then the forks. Not a job for the Saturday mechanic.

Posted on Apr 09, 2009

  • 1 Answer

SOURCE: Junp start my 1996 Suzuki 1400 Intruder

you can get to the battery without taking seat off, look just forward of rear wheel about 6inches off the ground

Posted on Apr 27, 2009

  • 190 Answers

SOURCE: backfiring and low compression in back cylinder

sounds if you have a burnt valve/s somewhere

Posted on May 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front brakes will not pressure up, what can I do and how do I do it?


two ways to try.go to the local auto store.get a vacuum brake bleeder.the next way can be time consuming.open the master cyl .make sure its full.open the bleed screw and wait for it to gravitate down.don't let it run empty.keep fluid in reservoir at all time.

May 17, 2014 | 1999 Suzuki VS 1400 Intruder

1 Answer

My front brakes will not pressure up, what can I do and how do I do it?


Then you have a master cylinder that is bad it will not hold the pressure. Change it out. Check when you pull the brake handle and look to see if there bubbles come up most likely it the master cyclinder.

May 17, 2014 | 1999 Suzuki VS 1400 Intruder

1 Answer

On my 96 Suzuki intruder 1400 I rebuilt the master brake cylinder, but I'm having trouble bleeding the brakes. They're still spongy no master what I do. Any suggestions are welcome.


Did you Bench Bleed the Master Cylinder before you installed it?

You have to work the AIR out of the system all the way down to the Wheels.. I did this once and it took me over 3 hours of Bleeding to get this done... Sorry

Apr 15, 2013 | Cars & Trucks

1 Answer

Suzuki Intruder 1400 1996, First to Second Gear is harsh!


Change the fluid in the clutch reservoir,bleed out the remaining fluid.(keep it full as you go) Should be dot 4 fluid not dot 3. U may need to rebuild the master cylinder or replace it.

Apr 24, 2010 | 1996 Suzuki VS 1400 Intruder

1 Answer

Backfiring and low compression in back cylinder


sounds if you have a burnt valve/s somewhere

May 13, 2009 | 1996 Suzuki VS 1400 Intruder

1 Answer

1999 1400 intruder does'nt have any pressure when engaged.


Maybe, and maybe not. If it is a problem with the master cylinder, then it could be bleeding back into the reservoir.

If it will not pump up and pressurize, and there are no signs of a leak, then you need to look at the master cylinder.

May 11, 2009 | 1999 Suzuki VS 1400 Intruder

1 Answer

Front brakes no preasure ??


Sounds like air in the master cylinder, bleed the front brakes till there is no air and try them. If there is still no pressure then more then likely, you need to replace the master.

May 02, 2009 | 1996 Suzuki VS 1400 Intruder

Not finding what you are looking for?
1996 Suzuki VS 1400 Intruder Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...