Question about 1997 kawasaki VN 1500 Vulcan Classic

Open Question

How to change turn signal on 97 vulcan 1500d classic

The rubber was old and cracked on the front turn signals, i removed the headlight, unplugged the signals and broke them the rest of the way off. I want to know the easiest way to remove the fork covers so when i get new turn signals i can install them myself! Thanks in advance

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2336 Answers

SOURCE: remove a gas tank

there are 2 bolts at the front of the seat, takeoff the seat, unsrew the bolts. that is the only thing holding it on. push the tank forward a bit, then lift up. there are breather tubes under the tank. be careful, they are difficult to get back on depending on the length. there are 2 bolts at the front of the seat, takeoff the seat, unsrew the bolts. that is the only thing holding it on. push the tank forward a bit, then lift up. there are breather tubes under the tank. be careful, they are difficult to get back on depending on the length.

Posted on Nov 10, 2008

  • 132 Answers

SOURCE: slow right turn signal on Kawasaki 800 Vulcan Classic.

there is only 1 flasher relay. unfotunately its a sealed type so you will have to replace it.

Posted on Jun 03, 2009

  • 491 Answers

SOURCE: Cannot remove the seat

yes the keys are for both , to release seat put pressure on seat then turn key

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 kawasaki vulcan classic 1600, the left rear turn signal was broke off. both front and rear turn signals quit working. I bought new signals for the rear, and both still dont work


Hi, Tom before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www2.vulcanrider.se/DL/Vn1600A1_2_sevman.pdf
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki/kawasaki-vulcan-owners-manuals

Oct 05, 2016 | 2006 kawasaki Vulcan 1600 Classic

1 Answer

How do I remove front right turn signal so I can install a new on a 2002 Vulcan 1500 Classic fi


Hi Zack, I am sorry you can't find the first and best tool you ever bought for your Kawasaki but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
https://www.tradebit.com/filesharing.php/search/0/2002+kawasaki+vn+1500+vulcan

Jul 29, 2015 | 2002 kawasaki VN 1500 Vulcan Classic

1 Answer

How to find the rear turn signal connectors on a 1997 Vulcan 800a I am replacing the originals due to rotting of the rubber do I have to remove any body parts to get to them????


If the 1997 Vulcan 800A has the same rear finder side chrome
trim as the 1996 Vulcan 800B the instillation will be as follows. I can't remember
for sure if you need to remove the chrome trim or maybe only loosen it enough
to run the wires. Remove the seat, for safety remove the negative battery
cable, loosen or remove the chrome side trim, trace the light wires to where
they plug into. Each side will have a separate plug in location. Each wire has
a color, one will be striped the other will be a solid color, when reconnecting
the wires make sure they are connected back to the proper color.

Sep 17, 2013 | 1996 kawasaki VN 800 Vulcan Classic

1 Answer

97 kawasaki vulcan 1500D classic igniter is obsolet, can the bike be re wired


We offer brand new built to order CDI Units for your bike on our website. You can order online at the link below or by calling the toll-free number. Hope this helps!
http://www.regulatorrectifier.com/catalog/1996-1997-Kawasaki-Vulcan-VN1500-D-Igniter-CDI-Unit

Toll Free # 1-877-239-4390

Mar 19, 2012 | Motorcycles

1 Answer

Replacing headlight on 1989 Toyota


if the turn signal cover is loose, and you are not really sure and dont want to break yours, visit your local junk yard and try the exact same thing there. But you could always try a rag and a flat head screwdriver, use the rag to cover the screwdriver and gently pry the turn signal lens out from the back of the housing. Usually the rubber grommets have just gotten old with age and weather. have you tried removing your headlight? although rare, somethimes the headlights need to come out first with certain models.

Oct 29, 2011 | 1989 Toyota Pickup SR5

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

1 Answer

How do replace turn signals for a different style


I don't know what kind of signals you are looking to put on but there is only two wires pos./neg. should unplug inside the headlight!

Oct 12, 2009 | 1998 kawasaki VN 800 A Vulcan

1 Answer

Need to replace Turn Signal Rubber. I cannot find anything on how to remove the Turn signals from the frame to get them where I can replace the Rubber Portins whice are Dry Rotted and Broken.


Okay, if I'm not mistaken, you have to remove the silver bar completely. On the underside of the bar should be a nut where the turn mounts to the bar. Just remove the nut and it should pop right off,

Aug 09, 2009 | 1996 kawasaki VN 1500 Vulcan Classic

2 Answers

Signal bulb on 2003 buick regal


To change front turn signal –
open the hood; look in back of headlight; two white clips; pull straight up, and then whole headlight comes out including turn signal; it is all one unit; remove rubber cover, then you take bulb out of unit. Mechanism that bulb fits in will need to be turned clockwise (looking from the front) and pulled to get it out of the larger unit holding all lights. Be sure and put rubber cover back on before re-inserting the two white clips.

Mar 16, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
1997 kawasaki VN 1500 Vulcan Classic Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...