Question about Gilera Runner VX 125 Motorcycles
Ive checked the spark plug it sparks and petrol is running into the carb as i turned the petrol on then pulled the fuel line out of the carb and it was coming out the end were it connects to the carb. ive tried kick start it and bump it. when i bump start it idles very quiet and then cuts out and i revved while it while it was idling but when i rev it while still pushing the bike after bumping it the revs seem as if they arnt catching if ya get me. havent tried take carb of yet as its too dark going clean the carb tomorrow and check if fuel is running throgh it to the engine wen its lite but any help on what too check will help greatly thanks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: kawasaki 300 bayou won't rev up.
No guarantees but try this. Pull the slide from the throat of the carb. Now move the clip on the jet needle down one notch. This will richen the low end mix. Two notches may be needed but do one notch at the start.
Posted on Apr 30, 2009
Remove the throttle stop adjuster and the air screw adjuster and spray carb cleaner in the holes.
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Turn the pilot screw 1/4 turn counter clockwise. Check the float level. Before putting the slide back in the throat of the carb, move the clip on the jet needle one notch lower.Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Adjust the idle speed with the Throttle stop screw. This process should get you back on the road. A “very helpful” rating for this answer? Thanks!
Posted on Jun 22, 2009
SOURCE: LEAKING OVERFLOW PROBLIM
it sounds to me like the carb float levels are out of adjustment and it is overfilling the bowls,or,the needle valve seats are worn and leaking,which will allow fuel to continue filling the bowls even though it looks like they are closed,remove the carbs from the bike,remove the bowls,turn the cabs upside down close the floats(push them right to the top,this simulates full bowls)then blow throgh the fuel inlet pipe,if you can hear air escaping from around the seats they are faulty,also check that the seats themselves are tight in the carb body,i dont know why but gsxr carbs seem to shake the valve seats loose..hope this helps
Posted on Jul 04, 2009
I had the same issue, and it after lots of testing and measuring, found out it was only that 'earth' wire that you have at the bottom left part of the engine, coming out from the left engine cover. You will find it easily, it's a standalone wire, mine had its sleeve too dry, might have been why it was not well connected. It also had a mix of sand and oil in it, so no wonder the lights would dim out. The wire plugs into some sort of a screw, you really can't miss it :) Even the old, worn sounding Yuasa battery got back to perfect function, only added distilled water to it and let it run fro some time. Cheers:)
Posted on Apr 06, 2010
Tips for a great answer:
Jun 10, 2014 | Boating
Feb 17, 2014 | Garden
Feb 03, 2012 | Homelite Mighty Lite Lawn Trimmer
Jan 24, 2012 | Mtd Garden
Aug 25, 2011 | 1998 Ford Explorer
Feb 27, 2011 | Troy Bilt 5.5hp Self Propelled Mower
Dec 14, 2010 | ATK 125 2-stroke Motorcycles
Aug 04, 2009 | 1995 Alfa Romeo 164
Jun 14, 2009 | McCulloch 16 In 4.5 Hp Electric Chainsaw...
Mar 11, 2009 | Husqvarna Chain Saw 20" Bar
Aug 07, 2013 | 2006 Gilera Runner VRX 200
Apr 06, 2013 | 2006 Gilera Runner VX 125
61 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: