Question about 2001 Ducati 996 S

1 Answer

I was pulling the tank off and didnt release the quickset release on the inlet valve. after noticing gas pouring out of the top of valve, i could tell the hex part of the flange kept spinning?Is the flange broke and i need new pump?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ducati Master
  • 40,765 Answers

Hi, Jackson for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. If necessary, transport your bike to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your problem. For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have a nice day.
Free Ducati Motorcycle Service Manuals for download
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance
Ducati 996 2001
the official tips and tricks thread Speedzilla Motorcycle Message Forums

Posted on Feb 07, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CHANGING INJECTED VT 750 FUEL FILTER


Most fuel filters are just like any other. Get the proper replacement part online or from a local Honda dealer.
The filter is in-line on the fuel hose (rubber hose coming from fuel tank). It has an inlet and an outlet - be sure you install it correctly as gas will only flow one way through the filter. The filter usually has an 'arrow' to indicate the direction of the flow or the word 'IN' for the inlet.
The hoses are held on by little clamps that should be easy to release.
Be sure to turn off the fuel supply with the fuel shut-off valve (if you have one), or pinch the supply-side of the hose with a small vise-grip pliers...otherwise gas will pour out all over.

Oct 18, 2014 | Honda VT 1100 C2 Shadow Sabre Motorcycles

1 Answer

Pw50 leaks gas


Hi, Anonymous "ABSOLUTELY" and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
PW50 carb won stop leaking fuel
Yamaha PW 50 checking carb
https://books.google.com/books?id=ozV8-Aer4N8C&pg=PA84&dq=pw50+manual&hl=en&ei=TCS2TcbdJ4PW0QG0z9jmDw&sa=X&oi=book_result&ct=result&resnum=1&ved=0CGUQ6AEwAA#v=onepage&q=pw50%20manual&f=false
OEM parts for Yamaha
Yamaha PW50Y Owner Manual

Jun 01, 2012 | 2005 Yamaha PW 50

1 Answer

Bike is very hard to start and leaks oil out of the wheep hole....and just notice alot of oil just below the fuel tank on top end...what could it be?


I have the displeasure out of tell people bad news about this bike, the valves on the crf line has been a problem since they can out. that's most likely the problem your haven. check you comprsion, is it low or not there at all? adj. your valves and see what happens with the starting. something else i have seen with the brute of a bike is the de-comp. lever starts to go out. what i mean by that is" it gets stuck" and wont release. look into that. as for the oil how much do you have in it?? does it smell like gas? i would do ahead and change it. and the oil under the tank when you pull the valve cover off you might find a bad gasket.
Let me know what you find
M.Woodring

Apr 20, 2011 | 2003 Honda CRF 450 R

1 Answer

Kenmore model 110 top load washer water drips out slowly, takes a long time to fill tank


Either the inlet hose screens or the water inlet valve screens or the the water inlet valves not opening completely. Check the screens and the water flow from the inlet hoses by removing them from the water inlet valves. The water valves are not opening properly and needs replacing if the screens are clear and the water flow from the inlet hoses are good.

Remove the cabinet to access and replace the water inlet valve assembly. Unplug the machine from the electrical supply then release the console from the top of the cabinet depending on the model of your machine then pull forward and up on the console and lay it back on the hinges.
5b58821.jpg

9dec9ac.jpg

5b4b40f.jpg

e5a5ab8.jpg

Disconnect the lid switch harness connector by pressing on the tab located in the middle and pulling it up.
9698f29.jpg

The cabinet is attached to the rear of the washer by two brass-colored retaining clips. Insert a flat blade screwdriver into the turned-up edge of the clip, located on both sides, and then pry back to release the clip from the slot in the cabinet.
4e2277c.jpg

Open and hold the lid while grabbing the cabinet front opening then tilt the top of the cabinet toward you by pulling the cabinet away from the base. This releases the front and back slots of the cabinet from the tabs in the front and back of the base.
8557e5b.jpg

Using the side of your leg and/or body as a support for the front of the cabinet, carefully lift up the cabinet and set it aside. You can now remove the water inlet valve assembly and install the new one then reassembly the machine.

Bring the cabinet to the front of the washer then slide the front bottom rail of the cabinet under the rail at the base of the machine then lay down the cabinet into position. Make sure the slots in the cabinet sit into the tabs at the base of machine.

Reconnect the lid switch harness then push the retaining clips back down into position to secure the cabinet to the rear of the machine. Reinstall and secure the console to complete the repair.

Sep 25, 2010 | Kenmore 15864/15862 Top Load Washer

1 Answer

We just got a new propane tank and connected it and propane is not coming through


I'll assume you had it purged of air before you had it filled, right? A full 20lb tank should weigh about 35-38 lbs. If so try this: Leave the tank valve closed for a few minutes. Then open the tank valve very slowly. It may have a built-in excess flow valve in the hose that is checking closed and preventing you from getting gas. See if that helps.

May 12, 2010 | Thermos QuickSet 462836203 (LP) Grill

1 Answer

Fuel-spit back from my 2005 Dodge Durango


WOO stop there is a major recall with the 05 durangos the check valves get stuck they are recalling the gas tanks on thousands of those car. that is a big fire hazard. Go to the dealer I garente ur vehcle is recalled u may have not gotten the notice in the mail yet. Please rate if this helps.

Here is a copy of the dealer recall notice.

2005 (HB) Dodge Durango
NOTE: This recall applies only to the above vehicles built from October 13, 2004
through November 30, 2004 (MDH101300 through 113023).
The fuel tank inlet check valve on about 18,900 of the above vehicles may stick in
the open position. This can cause fuel to spill out of the filler tube when the
vehicle is being refueled. Fuel in the presence of an ignition source can result in a
fire.
The fuel tank inlet check valve must be tested for proper operation. Vehicles with
a sticking check valve must have the fuel tank replaced.

Aug 11, 2009 | Dodge Durango Cars & Trucks

1 Answer

HEATER WAS WORKING FINE TILL I HAD PROPANE TANK TOPPED OFF


The Pressure Regulator may be stuck, Try closing the propane valve releasing the pressure,, gently tap the regulator( on the propane inlet side) and Very Very slowly open the propane tank valve, and attempt to light

Jul 30, 2009 | Hayward H Series

1 Answer

Water Heater Replacement


1) After shutting off the water and gas or power supply to the tank, connect a hose to the drain valve at the bottom of the tank, open the valve, and run it to a nearby drain or outdoors. Use two wrenches to unscrew the inlet and outlet fittings from the top of the tank. 2) For a gas water heater, shut off the gas inlet valve and use two wrenches to disconnect the union or flare fitting between the gas supply pipe and the inlet valve. Also remove the flue hat that expels gasses into the flue at the top of the tank. 3) After removing the old unit, set the new one in place with the controls and burner accessible. Allow at least 6 inches of clearance around its perimeter, and keep it away from flammable materials. Use a level to check it for plumb; shim the base with pieces of asphalt shingles or plastic wedges. 4) Wrap the threads of the heat trap fittings with pipe-wrap tape, and screw the fittings into the water heater (blue into the cold water inlet and red into the hotwater outlet). Be sure the arrows marked on the fittings point in the direction of water flow. 5) Install new flexible connectors on the water inlet and outlet pipes. If there is no shutoff valve on the cold water side, install one before connecting the water heater. After all connections are complete, open the shutoff valve to fill the tank. While it is filling, open several hot water faucets in the house to bleed off air in the pipes. 6) Assemble the gas pipes as shown. Spread pipe dope on the threads, and screw together the parts, tightening them with one pipe wrench on the pipe and another on the fitting. Follow the manufacturer's instructions for connecting the unit with gas supply tubing. After turning on the gas, test all connections by brushing soapy water on them and watching for bubbles.

Aug 27, 2008 | Stiebel Eltron Tankless Water Heater

Not finding what you are looking for?
2001 Ducati 996 S Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ducati Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

bobkoure

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Ducati Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...