Question about kawasaki KX 125 Motorcycles

1 Answer

Clutch not working on my kx 125 replaced cable pivot arm not returning

Just purchased bike for my son i was told by seller that it just needed a cable replaced cable and still not working if you pull in the clutch it stays in gear

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 46 Answers

The spring in the clutch basket makes the pivot getting back to is free play place.. you may remove the right side clutch cover and remove pressure plate to figured it out what hapens there... or you may have the bering from the pivot arm jammed or something with it...

Posted on Feb 12, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: bike stays in gear with clutch in

You are saying that with the clutch lever pulled in the bike still wants to go forward. Generally that is caused by dirty, gritty oil in the gearbox. Go ahead and change the oil. 10w40 motor oil is what you want. I think that will fix the problem assuming the clutch plates were installed properly. The first plate installed and the last plate installed should be a fiber friction plate, 8 plates total. A metal pressure plate goes between each fiber plate, 7 plates total.

Be sure the lever assembly arm is installed so that it gets full movement of the clutch cable. If the full range of movement is not present then full disengagement of the clutch is not going to happen.

cape cod bob did you a good service in the manual referral. Be sure to say thanks.

Posted on Apr 16, 2009

  • 1 Answer

SOURCE: 2003 KX125 Clutch Problem

have you checked the basket for groves? if it is groved the plates will stick the release all of a sudden.

Posted on Mar 15, 2009

goofduck
  • 490 Answers

SOURCE: my 1986 kx 125 clutch does not engage worked prior

possible the cable is needing to be adjusted make sure it is pulling on the pivot

Posted on Apr 15, 2009

co7196
  • 3433 Answers

SOURCE: clutch not working

What type oil in your crankcase? Wet clutches go on strike with wrong oil. Engine oil is a no no.

Posted on Jul 10, 2009

  • 1 Answer

SOURCE: clutch slipping

i have a honda cr 125 i put a new clutch , springs and 1st 2nd 5th are good but 3rd 4th are slipping. can some give me some help ! thank you

Posted on Oct 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch problems


Release arm in engine is broke.

Jun 06, 2013 | 2003 kawasaki KX 125

1 Answer

We have 75 125 ke. my son developed a problem where as soon as you release the clutch , it surges forward then dies instantly, i've tried adjusting clutch cable but with the same results, could this be...


No, this is a clutch problem. I love these bikes, wish I still had mine. Need new cable and probably clutch plates. It's very easy to change the clutch. If you get stuck email me at andydrinkell@yahoo.co.uk and I'll talk you through it.

Jun 30, 2011 | 1976 kawasaki KE 125

1 Answer

OK my 125 cc dirt bike the gas tank was leaking so I toke out the ring and then I ordered another one and the bike was standing for about 2 to 4 weeks in the cold then I changed the ring and I relized the...


Hi
Both seized.
For the gas tap, spray CRC lube on it, leave for an hour then gently use grips to move it.
For the clutch, need to know if its the cable or interanl clutch. Disconnect cable from engine and try, if OK its internal. If its clutch cable remove from bike and try to spray / fill cable and leave elevated for and hour / day. Then start see sawing cable to free up.

Dec 11, 2009 | 2005 kawasaki KX 250

2 Answers

Clutch slipping


Clutch plates are probably toasted. Drain the oil, remove the cover where the clutch cable goes into and check them out. Not hard to replace but you do need a special tool to get the plates off/on.

Aug 20, 2009 | 2003 kawasaki KX 125

1 Answer

Kx 125 2003


im pretty sure that the bike is a all in one menin that oil in tranny is same that flows in motor

Jul 22, 2009 | 2003 kawasaki KX 125

1 Answer

How do I install the clutch release shaft on a KX 125?


The clutch arm where the cable connects is on the left and it connects to the clutch via a shaft that pushes a rod which then pushes a ball bearing sitting in the holder and then the holder pushes the clutch operating plate to dis-engage the clutch. The only seal is on the clutch arm shaft that goes into the casing. At worst, only the springs on the operating plate would need to be removed then a 1/4" inward push on the rod from the right side would give clearance for the shaft to be inserted.
.
Go to the site below where you can see a parts diagram for your specific bike. You will select the actual brand, year, model, etc., once you go to the site. Part numbers and prices are also shown. You can order parts from this site. In the event no price is shown on a particular part, the part is not in stock. www.babbittsonline.com/pages/parts/viewbybrandand/parts.aspx

A “very helpful” rating for this answer? Thanks!

Jun 11, 2009 | 2003 kawasaki KX 125

1 Answer

Clutch cable problems


a little clip the fastens the arm on.

May 14, 2009 | 2003 Yamaha YZ 125

1 Answer

Hi i have a kawasaki kx 125 1991 motocross bike,my problem is when running it will not go out of gear i have just fitted a clutch cable but its still the same,could it be i need new sprigs/plats or just...


it feel like the actuation of you're clutch lever does not disengage you're clutch plate ...i will think that you're clutch actuation arm ( the one the clutch cable get in... is not engage at the right place or the arm is not on the right spline)...spring and plate only is an issue when the clutch is sliping....

May 12, 2009 | kawasaki Full Suspension Mountain Bike Men

2 Answers

Bike stays in gear with clutch in


You are saying that with the clutch lever pulled in the bike still wants to go forward. Generally that is caused by dirty, gritty oil in the gearbox. Go ahead and change the oil. 10w40 motor oil is what you want. I think that will fix the problem assuming the clutch plates were installed properly. The first plate installed and the last plate installed should be a fiber friction plate, 8 plates total. A metal pressure plate goes between each fiber plate, 7 plates total.

Be sure the lever assembly arm is installed so that it gets full movement of the clutch cable. If the full range of movement is not present then full disengagement of the clutch is not going to happen.

cape cod bob did you a good service in the manual referral. Be sure to say thanks.

Apr 16, 2009 | 2003 Yamaha YZ 125

1 Answer

My 1986 kx 125 clutch does not engage worked prior


possible the cable is needing to be adjusted make sure it is pulling on the pivot

Apr 15, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...