I need to know torque specs and torque pattern for a 2001 head gasket on my 2001 sunfire

Question edited for clarity.
Question moved to model category.

Head bolt torque specs and pattern

EvolutionM.net https://www.evolutionm.net > ... > Lancer Engine Tech

Jun 6, 2009 - Lancer Engine Tech - Head bolt torque specs and pattern - Hey all. Before anyone flames in case there is a post, I did use the search ...

2003 Mistubishi Lancer ES Head Torque Sequence, HELP!
Sep 15, 2011
Torque Specs for Head - EvolutionM - Mitsubishi Lancer and ...
Mar 5, 2007
Need some help..torque specs. - EvolutionM
Dec 16, 2009
what sequence do the head bolts need tightened - EvolutionM
May 28, 2011
More results from www.evolutionm.net

..

12-13 foot pounds

Pontiac Engine Torque Specs

Butler Performance https://butlerperformance.com > p-34888-pontiac-engi...
Pontiac Engine Torque Specs ; Oil Pump Cover Bolts, Engine Oil, 15 ft-lbs. ; Windage Tray, Engine Oil, 15 ft-lbs. ; Oil Pan, Engine Oil, 12 ft-lbs. ; Camshaft ...

Oil and Transmission Pan Bolts. How much torque?

GMForum.com https://www.gmforum.com > ... > 1992-1999
Jun 12, 2003 - the Torque Specifications for the Xmission Oil Pan Bolts are 12-13 Ft. Lbs. Works for me.

Transmission pan Torque spec
Apr 28, 2017
4T65E-HD transmission pan bolt torque values
Feb 8, 2008
More results from www.gmforum.com

2004 Pontiac Sunfire 2-dr Transmission Pan Gasket ...

MyCarSpecs https://www.mycarspecs.com > pontiac > sunfire > 2004
The transmission pan gasket helps to seal in transmission fluid and keep it from leaking everywhere. This will degrade over time and need replacement, ...

..

If you have it apart, you should know already. If not, and you're doing this right, it should have four bolts, correct? I wouldn't worry about torquing them to anything specific, I'd tighten them snugly, then maybe 1/8 to 1/4 turn more in a criss-cross pattern. should be fine, they're not head bolts or lug nuts, so torque specs aren't necessary, but if you REALLY need the torque spec, I'd suggest going into an f-150 forum, sounds like a logical thing to do.

Doug, Torquing multiple bolts, like on a cylinder head are shown in last video link.Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www4.briggsandstratton.com/miscpdfs/RNT/Engine%20Specifications%20Chart_ms3992.pdf
FAQ Small Engine Specifications Briggs Stratton Specs
Engine mounting pattern
HOW TO LOOK UP AND TORQUE BRIGGS HEAD
How to replace Briggs Stratton Intek Head Gasket Pt 2

here is a link for all the torque specs for a Volkswagen 2.0L

Try this page http://www.torkspec.com/torkspecme.aspx

cylinder head bolts short bolts 43 ft lbs long bolts 46 ft lbs.

rocker arm bolts 22 ft lbs.

Install cylinder head bolts finger-tight. New cylinder head bolts are recommended due to stretch of the old bolts.
Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm)

Install pushrode and rocker arms and rocker arm nuts. Tighten nuts to 22 ft. lbs. (30 Nm).

Install valve cover and tighten bolts to 89 inch lbs. (10 Nm).

Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines




Fig. Cylinder head bolt tightening sequence-2005 3.4L engines



Hope this help (remember rated and comment this).

When torquing items today very little is done with just "numbers" in the process. Now you have to have an angle meter to complete the process so when you see me say to torque a specific number "plus so many degrees", this is how it's done. This is the meter: Now, Here are the specs for installing the head:
Cylinder Head Bolt

• First Pass

30 N·m
22 lb ft

• Final Pass

155 degrees


Here is the sequence shown in picture form:
Also, you will need to discard the old bolts because they are "torque to yeild" bolts and CANNOT be reused. The reason: "Torque to yeild" bolts actually stretch during the torque process and once they've gone through this process they can't be reused because they no longer are able to "clamp" the head because they are too long. Hope this helps your repair project.