Tip & How-To about Motorcycles

Skyjet SJ-125-23 Common Problems/Solutions

Neutral light Never showing

  • This could be a simple shipping issue, Which if you look on the left hand side of frame in centre below seat and just under petrol tankthere is a GREEN wire, Which is normally not-connected or dis-lodged when riding, Connect wire back to other green wire near it heading towards gearboxIssue will then be sorted and electric start will now work.
Oil leaking from Left hand crank case near gear shifter
  • This is caused mainly by wear and tear on the gasket for the left crank case, just remove start motor cover carefully without loosing anything, Then Remove old paper gasket replace with new Copper gasket And/or Gasket sealant/maker bought from any HALFORDS shop for about £5
Oil pours out when I remove screw for manual turning of piston on left crank case
  • Unlike normal engines which this part would remain dry at all times, The skyjet engine which is basedof a Old CG-125 push rod engine, Oil pouring into that side and out the screw when un-screwed is commonso don't worry about anything breaking, However its recommended to empty oil from the main oil empting screwunder engine which is a 17MM Bolt and draining fully before removing any of engine casings.
Where can i buy the cheap parts for Skyjet Motorbike
  • However due to skyjet is no longer listed, Buyers must look for the kasiar parts they are exactly the same, However may be colour differences for some engine parts but the difference is instead of normal black parts which sky-jet engine has there Silver instead

Posted by on

Motorcycles Logo

Related Topics:

Related Questions:

1 Answer

I have a Ve commodore sidi and can't find the fuel pump relay. Book shows it at passengers footwell but it isn't there


Hi Joel If not in left side kick panel(early models).Normally above or below fuse remover clip.
Check left side of boot in rear electrical centre. Should be in hand book, should also be a picture in the fuse cover
If neither of these places may not have a relay it will be dependent on type of fuel system.You have not stated why you require to find fuel pump relay. Do you have a start or running issue?

May 08, 2017 | 1998 Holden VT Commodore

1 Answer

where is the vin number located on a 1999 kawaski mule, need help asap thanks


For most late-model Mule™ side x side, the VIN is located on the forward frame rail below the seat. For all Trans4X4® models, the VIN is on the left rear driver seat frame rail, and Mule™ 600/610 4X4 models have it on the frame rail below the seat over the fuel tank. On most older Mule models, the VIN is near the front of the vehicle

Feb 21, 2017 | Cars & Trucks

1 Answer

why green light wont come on when put in netural to start


Hi Howard find thd neutral switch on the left hand side near the sprocket it should be a single wire (light green) earth it to the frame or battery and se if the light comes on. If it dose make sure it's in nethral then try to star it. Regards Jim...

May 05, 2015 | Honda 2008 FourTrax Rancher ES

1 Answer

Can the headlights be adjusted in 2013 Camry


Yes they should be adjustable because people change tyre profiles front to rear and this alters the drive angle.The adjustment screws are in the headlamp housing behind lamps accessed from the hood/ bonnet side.you do need to do this properly so they align together at the legal height for full beam.there is plenty of online information on the correct height for full beam...once you have made sure all Your tyres are at the right pressure....park on level ground ...at least 3 meters from front of a wall ....and at right angles to the wall....measure the height to the centre of headlight to ground .......mark the right light horizontal line for correct height on the wall and make sure you put lights on full beam....they should shine slightly below (say an inch )to the marked the measurement of height of lamp on the vehicle....adjust until the right hand light horizon is an inch below...now mark vertical line to cross centre of reflected light....this will give you a register point to mark where the left light should fall ...this will be exact distance apart as on vehicle and again adjust left until it falls below 1inch of the measured height line of lamp on car......mark distance from right to left light and mark the same height in chalk....then adjust left light to pinpoint marked chalk cross.adjust the beams by turning the spring loaded screws behind the lights.once you are happy check dipped positions....on right hand drive the lights should dip below and left.left hand drive dip below and right.you probably didn't need so much info but ...hey it's free and it saves any misunderstanding.hope this is of help...please vote.thankyou.

Feb 07, 2015 | Cars & Trucks

Not finding what you are looking for?

3,234 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Loading...