20 Most Recent 2002 kawasaki KLE 500 Questions & Answers

Phillips H4 - 55w/60 or use the same H4 but the HID ones. Cheers

All decent auction internet sites, like ebay, have for sale such things. Check it out as alternator.

There are 3 positions (as you probably know). Reserve, on and prime. Under normal conditions with a properly working fuel tap, prime is the by-pass that allows fuel to flow through without the engine running. On and reserve will only allow fuel to pass when the engine is running (uses vacuum from the carb).

• PRIME has the handle facing down
• ON is when it is facing the front
• RESERVE when it faces the rear.

Do not leave the tap in the prime position EVER as this allows the fuel to fill the carb and with the engine running or attempting to start will cause hydrolock that will bend the pistons con-rods. Only use it to fill the carb with fuel and turn it to on or reserve as soon as you can. If the bike runs using the prime position but will not run when on or reserve, then you may have a vacuum problem or a dodgy tap......assuming you have fuel that is. Hope that helps.

ALL DEPENDS WHERE ARE THE DAMPERS. THERE IS SOME THAT HOLD THE GAS TANK AMONG OTHERS>.

By low voltage do you mean your battery, if not and your battery is good you will need to do a test on the coils, resistance and IB if it is neccasary, also check the pulse coil or crankshaft sensor, Igniter etc, It doesn't take long but there are several areas and also check all connectors and fuses corrosion loosness blown contact etc. If you have had any work done on the bike at the time trouble began start there. Here is a web site that has the wiring diagram for the bike. diagramwiring.net let me know if you need anything else K

Babbitt's has them in stock. www.babbittsonline.com You may want to Google motorcycle salvage kawasaki to see what you can find.

The bike was left for a long time, the must be discharged.
1) Charge fully the battery (if not charging change the battery)
2) Ove-haul the carburator, clean all the jets for jelly like deposit.

Note: after some time the gasoline dries up leaving a jelly like deposit inside the carburator and must be removed.

if the speedo is not working check the speedo cable if its broken,,check your brake resevuors for fluid,,they may need a bleed also

cant help with lock, try some graphite powder.
left switch will have high and low beam( H and L) and a horn.(and possibly headlight on off,but this is usally on right hand side)
Pri is prime, only to be used to help start bike if you have run out of fuel, this bypasses the vacumn fuel tap, do not ride, park or leave it on pri.
refill when it runs out and you need to switch to reserve, if you take a note of the odometer reading when you fill, you can figure out how far it goes on a tank full and plan your trips, the reserve is to get you the 10-20klms to the next station.

It is is firing out of the carb and the exhaust, the timing must be off, but also slipping. Is the flywheel tight? https://www.google.com/search?q=1984+kawasaki+klt+250+backfiring+problem ..

Not mentioned anywhere https://www.google.com/search?q=kawasaki+eliminator+%22EL+175%22+carburetor+size Lots of information for the bigger ones, 'Eliminator' is a whole range of models 125cc to 900cc https://www.google.com/search?q=kawasaki+eliminator+%22EL+175%22+carburetor+replacement ..

Absolutely, the rectifier on your Kawasaki Mean Streak 1500 can be repositioned during a customization project. The rectifier is a crucial part of the motorcycle's electrical system, converting alternating current (AC) from the stator into direct current (DC) to charge the battery and power the bike's electrical components. While relocating the rectifier, it's important to consider a few key factors:

1. Space and Mounting: Assess the available space on the motorcycle to find a suitable location for the rectifier. Ensure that the new position allows for proper mounting and secure attachment without interfering with other components or the bike's functionality.
2. Heat Dissipation: The rectifier generates heat during operation, so it's essential to relocate it to an area with adequate airflow for cooling. Mounting it in a well-ventilated area helps prevent overheating issues.
3. Wiring and Connections: When moving the rectifier, ensure that the wiring can be appropriately rerouted to reach its new location. Take care to maintain proper electrical connections and ensure a secure, stable wiring setup.
4. Protection: Consider adding protective measures, such as shields or guards, to safeguard the relocated rectifier from road debris, water, or other potential hazards.

Modifying the placement of the rectifier may require custom brackets, mounts, or fabrication work to secure it in the desired location. It's crucial to execute the relocation carefully, maintaining proper electrical connections and ensuring the rectifier's safety and functionality. If you're not confident in performing these modifications yourself, consulting a professional motorcycle mechanic or technician with experience in customizations can be highly beneficial. They can offer guidance, expertise, and ensure that the modifications are carried out safely and effectively.

eBay is the only place and there is only one. https://www.ebay.com/itm/266382749570 Or direct from China https://power-tool-batteries.en.made-in-china.com/product/tqRnSCOglNhK/China-Kawasaki-Power-Tool-Batteries-21-6V-Replacement.html Or you can open it up and solder in the individual NiCad cells. Better to replace with NiMH. This is probably why they don't exist, RECALL on the charger. https://www.cpsc.gov/Recalls/2007/alltrade-tools-recalls-power-tool-battery-chargers-due-to-burn-and-laceration-hazards ..

IGNITION SYSTEM for Kawasaki GT750 1992 # KAWASAKI - Online Genuine Spare Parts Catalogue (bike-parts-kawa.com)

We are in North America, so this link might work better for you than it does for me. I can only find a Parts Catalogue and an Owner Manual. https://www.google.com/search?q=kawasaki+kaze+zx130+service+manual ..

I'm assuming you have already checked the actual bulb is still OK? The bike uses a 'twin element' bulb so the tail light element might still work but the brake light element has blown. It's designed to be two bulbs in one so it takes up less space.On a lot of vehicles some electrical features share a fuse and only some of them are marked on the fuse box lid. Has anything else stopped working? On some Kawasaki bikes the brake light shares a fuse with the horn and the tail light so if the fuse has blown all three won't be working. Check the fuse labelled as the Horn to see if that has 'Popped'.*NOTE* ONLY replace fuses with one of the SAME Amp rating as lower 'A' fuses will blow and higher 'A' fuses won't protect your electrics.Bulbs and fuses are usually cheap to buy so you could replace them anyway before thinking it's going to be a 'Big' repair.

If your Kawasaki ZZR600 suddenly stopped firing, there are several possible reasons for this. Here are some troubleshooting steps you can take to identify and resolve the issue:

1. Check the battery: A weak or dead battery can prevent the engine from starting. Make sure the battery is fully charged and has a voltage of at least 12.5 volts.
2. Check the spark plugs: The spark plugs may be fouled, worn out, or damaged. Remove the spark plugs and inspect them for signs of wear or damage. If necessary, replace the spark plugs.
3. Check the ignition system: The ignition coils, ignition module, and wiring may be faulty. Use a multimeter to test the resistance of the coils and check the wiring for continuity. Replace any faulty components as needed.
4. Check the fuel system: The fuel filter may be clogged, the fuel pump may be faulty, or there may be a problem with the fuel injectors. Check the fuel pressure and flow, and inspect the fuel filter and injectors for any signs of clogging or damage.
5. Check the carburetor (if applicable): If your ZZR600 has a carburetor, it may be dirty or clogged. Remove the carburetor and clean it thoroughly with carburetor cleaner.
6. Check the camshaft timing: If the camshaft timing is off, the engine may not fire properly. Check the timing marks and adjust the camshaft if necessary.

If none of these steps resolve the issue, you may need to take your ZZR600 to a qualified mechanic for further diagnosis and repair.