20 Most Recent
1989 Honda Pacific Coast Questions & Answers
Wheres the petcock or on off valve
if you cant see it easy then you probably dont have one as you may have a electric fuel pump and dont require one as fuel auto shuts off ! P...
Lost manual of 1989 Honda Pacific Coast Where is
Brother, the fusebox is located under the small left air-duct cover.
Pull it out and locate it at the right above. Slide it off to eight o clock.
The placement of the fuses is only at the bottom of the cover.
Do not lose it and remove the Parking fuse. 2:/
Alfred
How is the fuel supplied to the cabs on !989m PC Honda
on all motorcycles not fuel injected there is a hose going from the bottom of the tank to the carburator...if it is fuel injected then there will be a fuel pump, and injuctors...more than likely steel lines going to the intake manifold
WHILE DRIVING IT DIED LOST ALL POWER ELCTRICAL
That's happened to me so many times, I've lost count. It's almost always one of two things: a wire shorted to the frame, or a loose wire connection. These two issues are almost always in, or near downstream of, the battery circuit. Good luck.
Honda pc 800 wont start if in gear
Sounds like the clutch switch is failed. Try pulling the wires off the clutch switch(on the handlebars by the clutch lever) and connect them together with a paperclip. If the bike will start in gear, the switch is bad.
1990 pc800
Starter Removal:
- Remove the Engine heat cover.
- Remove the Left crankcase cover.
- With the ignition switch OFF, remove the negative cable at the battery before servicing the starter motor.
- Remove the Starter drive gear shaft/gear.
- Drain the Radiator coolant. Remove the rear cylinder water hose connector.
- Disconnect the Starter motor cable. Remove the rubber cap and remove the nut.
- Remove the Starter motor mounting bold.
- Remove the Ground cable terminal.
- Remove the Starter motor.
Starter Installation:
- Install the Starter motor. Apply engine oil to the o-ring.
- Reconnect the Ground cable terminal.
- Install the Starter motor mounting bolt.
- Install the Starter motor cable. Connect the cable, tighten the nut and install the rubber cap.
- Install the Rear cylinder water hose connector. Apply engine oil to the new o-ring and install the connector onto the rear cylinder.
- Install the Starter drive gear shaft/gear. Install the starter drive gear with the "OUTSIDE" mark on the gear facing out.
I’m happy to help further over the phone at
https://www.6ya.com/expert/jeremy_69f3cc28d95bf514
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
Not finding what you are looking for?