20 Most Recent
2001 Ducati ST4S Questions & Answers
Wheel bearings
if they are the same as the older models....
SKF #6005-2RS
Measurements - 25mm ID x 47mm OD x 12mm width . It is often not recommended to remove the bearing and then reinstall it because there is a concern that the bearing could be damaged in its removal. This is because the bearing is installed by the outer race which does not put pressures or impacts on the bearings themselves but in the removal process the bearings are driven out by the inner race which puts a lot of force impact, and stresses on the bearings.
If the bearings are the ones that I listed (I believe they probably are), then you may be able to find them at a local automotice parts supplier such as Auto Zone, Advance Auto, or other place, as this size is fairly common.
Also, if you have the newer style spacer in the hub, you may need a blind bearing puller because you simply cannot push the spacer over to get to the inner race of the bearing. There is one notch on one side of the spacer, and it is a bit of a PITA to catch the lip of the inner race with a punch or screwdriver. Here is a picture of the newer style spacer that has ribbing on it....,,,
My ducati X diavel doesn't start how do I solve the problem?
When your 2016 Ducati X Diavel doesn't start, there are several steps you can take to try and diagnose and resolve the issue. Here are some troubleshooting steps you can follow:
1. Check the battery: Ensure that the battery is charged and in good condition. Check the battery connections to make sure they are secure and clean. If the battery is weak or faulty, consider charging or replacing it.
2. Ignition switch and kill switch: Verify that the ignition switch is turned on and the kill switch is in the "Run" or "On" position. Sometimes, these switches can accidentally get bumped or turned off, preventing the bike from starting.
3. Fuel level and fuel delivery: Confirm that there is enough fuel in the tank. Additionally, check for any clogged fuel filters or fuel lines that may be restricting fuel flow. If necessary, clean or replace these components.
4. Kickstand position: Some motorcycles have a safety feature that prevents the engine from starting if the kickstand is down. Ensure that the kickstand is fully retracted and try starting the bike again.
5. Spark plugs: Examine the spark plugs for any signs of fouling, wear, or damage. If needed, clean or replace the spark plugs according to the manufacturer's specifications.
6. Fuses: Inspect the fuses to see if any have blown. Replace any blown fuses with the appropriate type and rating.
7. Immobilizer system: If your Ducati X Diavel is equipped with an immobilizer system, ensure that the key you are using is programmed correctly and recognized by the system. Consult your owner's manual for specific instructions on the immobilizer system.
If the issue persists after these steps, it is recommended to consult a professional Ducati technician or authorized Ducati service center. They will have the expertise and specialized diagnostic equipment to diagnose and resolve the problem with your 2016 Ducati X Diavel.
6/11/2023 6:02:48 AM •
Ducati...
•
Answered
on Jun 11, 2023
Ducati X diavel doesn't want to start it only cranks the engine please help
Go back to basics to figure this out. An engine needs 3 things to start and run. Air, Fuel and Spark. Remove any one of these and it won't start. Try this.
What EXACTLY does it do when you press the start button
-Nothing at all or a slow sluggish crank is most likely a flat or bad battery issue. Charge or replace the battery.
Cranking at normal speed but not trying to start is possibly a spark supply issue. Test for spark at the plugs and work through the ignition from there.
Cranking, coughing and trying but won't idle is commonly a fuel supply issue. Check you actually have fuel in the tank. Yes, I've made that mistake! I've also forgotten to open the fuel valve. Check you are getting fuel to the cylinders. A way to do this is by removing 1 plug wire and cranking the engine for 1 to 2 seconds. Remove the spark plug on that side and sniff it. A working set up and it'll smell of fuel. Refit the plug and the wire and repeat this for the other cylinder. From there work backwards through the fuel system checking the injector, fuel pump and the fuel pipe lines.
3/28/2023 4:35:36 PM •
Ducati...
•
Answered
on Mar 28, 2023
I lost my key hot wire 2000 ducati monster
You may likely have to program a new key as it has a chip. The SBB key programmer on Ebay is great for cars but not sure about bikes but perhaps! Make sure your model is available in the indications given by the SBB programmer site on Ebay.
3/14/2022 7:15:18 AM •
Ducati...
•
Answered
on Mar 14, 2022
2000 748. What causes intermittent power?
Switch is worn . First take som rubbin alcohol and pour it on the switch. It can bring electrix back to life. But umay hav to buy part on acyclsalvage site or dealership
3/14/2022 7:14:38 AM •
Ducati...
•
Answered
on Mar 14, 2022
Would a 8inch pull back and 5 inch rise work for a Ducati Monster handle bars
Clearance issues aside, you need the proper mounts. If they make them, they will work, aside from tank clearance issues. If they don't make the proper kit, just don't do it. Handlebars are not something to experiment with when you're traveling down the highway at 60+ mph. Ever had a simple grip come off? Not fun, trust me.
7/27/2019 7:18:01 AM •
Ducati...
•
Answered
on Jul 27, 2019
Not finding what you are looking for?