20 Most Recent
2011 Modenas Dinamik - Page 6 Questions & Answers
My driver on my activa dx-3h20a will not turn
If the driver on your Activa DX-3H20A is not turning, there could be several possible causes. Here are a few troubleshooting steps you can try:
- Check the power source: Ensure that the power supply to the driver is properly connected and providing the correct voltage. Check the power cord and any switches or controls associated with the driver to ensure they are in the correct position.
- Inspect the motor: The issue may lie with the motor itself. Check for any loose connections or damaged wiring that may be preventing the motor from receiving power. If you have access to a multimeter, you can use it to check for continuity and voltage at various points in the motor circuit.
- Check the drive mechanism: Examine the drive mechanism of the driver, including belts, gears, and pulleys, for any signs of damage, wear, or misalignment. Make sure everything is properly lubricated and functioning smoothly. Tighten any loose components as necessary.
- Consult the user manual: If you have the user manual for your Activa DX-3H20A, refer to it for specific troubleshooting steps and guidance provided by the manufacturer. It may have additional information or troubleshooting tips specific to your model.
6/28/2023 4:54:39 AM •
Motorcycles
•
Answered
on Jun 28, 2023
Can't get over 50 mph on a 99 vz800
Check that it is running on both cylinders. If plugs are fresh, pull them and compare. If one still looks like new out of the box then that cylinder is not firing. Or if you have an infrared temperature probe, check the exhaust temp at each pipe is the same.
6/9/2023 1:58:04 AM •
Motorcycles
•
Answered
on Jun 09, 2023
Why is my jetta's 1995 clx 1.8L choke causing my car to cut out?
Recheck all your cable connections to the carb are correct and the cable routes are not kinked. This can sometimes cause tight spots on the cable making the choke cable stick and not work correctly. As long as you didn't change anything on the original carb when you took it off your lean/rich mixture should be correct.
Is this happening as you're pushing the choke Off or does it happen when you pull it back out to the On position when the engine is already warm? If it's happening when you trying to turn the choke Off it is often a sign the fuel jets on the carb are clogged or dirty, starving the engine of fuel. Get all the jets cleaned by someone who knows what they are doing and see if that helps The choke is simply a flap, that when you pull the choke on, starves the carb of air creating a deliberate 'rich' fuel mixture. This sounds like turning the choke off starves the carb of that extra fuel and stalls the engine.
6/8/2023 8:17:09 PM •
Motorcycles
•
Answered
on Jun 08, 2023
Wat is the best grade of petrol for my big boy 250 tsr motorcycle? (93 or 95)
lost the users guide already (under a year)
no country told some have octane (station) as low as 88.(ouch)
read the manual it tells you what to run!
95 octane should be good.
is this and AFRICAN mc?
I'D DO 95 DUE TO ENGINE RUNS REAL HOT; AIR COOLED IT IS
SO IF IT GETS TOO HOT ,NOT GET PING.(DETONATION)
6/6/2023 12:45:02 PM •
Motorcycles
•
Answered
on Jun 06, 2023
What is code b6104 on my 2009 street glide?
Are you sure those numbers are correct? Trouble codes normally start with a 0, 1 or a 2. Was there any other information with the code. Some Harley models use 3 or 4 letter codes as well to refer to the system where the issue is.
5/27/2023 11:30:44 AM •
Motorcycles
•
Answered
on May 27, 2023
On a 50cc tao tao is both head lights supposed to be on when the bright switch is in the on position?
In general, it depends on the specific model and wiring of the TaoTao scooter or moped. Some models may have both headlights turn on when the bright switch is in the on position, while others may have one headlight switch to a brighter setting while the other remains on a dim setting. It's best to refer to the owner's manual for your specific model of TaoTao scooter or moped to find out the exact details of its headlight system and operation.
5/25/2023 12:12:47 AM •
Motorcycles
•
Answered
on May 25, 2023
Motorycyle. with manual clutch
Husaberg 2011 TE250 - Am struggling to find gears - and at times change does not happen, with over-rev in same gear.
- all cars or trucks or MOTORCYCLES.W/ (MANUAL BOX , MANUAL CLUTCH)
- WE MAKE SURE CLUTCH IS WORKING FIRST. AND DOES NOT SLIP AND OVER-REV NOR DRAG. THEN COMES
- THE BOX., THE SHIFT FORKS AND DRUM INSIDE ARE PROBABLY GOOD IF OIL LUBE IS NEVER ALLOWED TO DRY OR BAD.
- NEXT IS THE SHIFT LEVER ADJUSTED WRONG.
- GET THE BIKE SERVICED, IN A REAL SHOP, CLUTCH FIRST.
- IS CLUTCH CABLE DRIVE OR HYDRAULIC, IS THE MASTER CYLINDER NEAR DRY ON THE LATER????????
ONLY 1 QUESTION , DO YOU ALWAYS USE THE CLUTCH TO SHIFT
IF NOT THE GEARS ARE A WRECK.
BUY THE SERVICE MANUAL AND SEE ALL PART AND WHAT MUST BE DONE TO GAIN ACCESS TO THEM ALL.
5/23/2023 12:49:51 PM •
Motorcycles
•
Answered
on May 23, 2023
Not finding what you are looking for?