20 Most Recent 2006 Harley Davidson FLSTN Softail Deluxe Questions & Answers

Hi, Anonymous the usual suspects are: 1. Spark plugs in bad condition or partially fouled. 2. Spark plug cables in bad condition and leaking check for spark leakage in the dark. 3. Spark plug gap too close or too wide. 4. Faulty ignition coil, module, and or sensor. 5. Battery nearly discharged. 6. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. 7. Intermittent short circuit due to damaged wire insulation. 8. Dirty air filter 9. Intake air leak. 10. Water, dirt, or rust in the fuel system, fuel pump and/or filter. 11. Old dead or bad fuel. 12. A faulty fuel pressure regulator. 13. Pinholes in the in-tank plastic convoluted tubing from the pressure regulator to the quick disconnect check valve. 14. Fuel tank vent system plugged. 15. Quick disconnect check valve sticking. 16. The throttle body controls misadjusted. 17. Damaged throttle body or intake seals. 18. Clogged or faulty fuel injectors. 19. Loose, dirty, or corroded ignition module connector at crankcase. 20. Faulty TPS, MAP, CKP, O2, and/or CMP sensors. 21. Incorrect valve timing. 22. Weak or broken valve springs. 23. Damaged intake or exhaust valve. 24. The control module may be in limp mode. 25. Check for engine trouble codes. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected]. Good luck and have a wonderful day. https://www.hdforums.com/forum/softail-models/1176410-06-backfiring-out-of-intake-wont-idle.html http://www.mediafire.com/file/bueyzhc4oxaz3g1/2006+Harley+Softail+Service+Manual.pdf http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc httpsownersmanuals2.com Harley-Davidson Softail-deluxe-efi-2006-owners-manual-66451 https://play.google.com/store/apps/details?id=com.fixya.mobile.android.sixya&hl=en_US&gl=US to speak to me personally

Denise, Ask/call your local Harley Davidson dealer for primary oil use for the climate you are presently driving in. Check the attached links,instruction and guides, Good luck "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." 2006 Harley Davidson Softail Deluxe EFI FLSTNI Primary Oil Maintenance and Lubrication https://answers.yahoo.com/question/index?qid=20090827074211AAucYJf Free Harley Davidson Motorcycle Service Manuals for download

Thomas, Harley rear brake anti rattle clip, Check the attached links,instruction and guides, this is what I could find online,Good luck. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." http://www.harley-davidson.com/en_US/Media/downloads/Service/isheets/-J01727.pdf http://www.harley-davidson.com/app-content/service/isheets/-J03708.PDF Rear Brake Pad Install Harley Davidson Forums

Probably the idle is too low for some reason

If you got any magnetism near the left side wheel bearing you will have destroyed its sensing/signalling ability. The magnetic pickup should only go back on one way in one position but check that it is located near the sensing wheel bearing. When it goes on it should be rotated up If the wheel somehow got mixed up and on backwards the magnetic bearing would be on the wrong side, away from the pickup. Check your wiring for damage. Never pull the wheel speed sensor cable taut or use it to support any other parts. Install the wheel speed sensor with the index pin on the out-board side or the sensor will be damaged. After the axle is installed rotate the front wheel speed sensor until the index pin makes contact with the shoulder on the fork slider and then route the wheel speed sensor cable up to the lower fork bracket along with the brake hose. If installing a new sensor on a Road King and other Fork mounted fairing models turn the front wheel to the right fork stop and then feed the connector up through the opening in the front of the lower fork bracket and connect it to the socket housing. If installing a new sensor on a frame mounted fairing model first turn the front wheel to the right fork stop and then connect the front wheel speed sensor connector and feed the connector under the main wiring harness conduit into the left side of the fairing bracket. In all cases secure the sensor cable and fender tip lamp wires using three cable straps as follows by capturing the front wheel speed sensor cable and brake hose at the brake hose lower crimp and then about the middle of the way between the upper and lower brake hose crimps and securing both the wheel speed sensor cable and the brake hose along with the front fender tip lamp wires, if is has a fender tip lamp. THEN about 2.5 in. (63.5 mm) below the brake hose upper crimp secure the front wheel speed sensor cable, the brake hose and again, if there is a fender tip lamp, the front fender tip lamp wires. The I insert the front wheel speed sensor cable in the clip by pushing on the lip at the rear of the clip to disengage it from the bracket, rotate the tab stamped ABS rearward until the clip is perpendicular to the bracket and install the cable and then rotate the tab forward and apply pressure until the lip engages and then gently pull the cable to verify that the clip is installed properly.

I don't have a setting for that particular carb either. This is not uncommon when dealing with the Japanese carbs. Just set the float level the same as previous year models. The difference in the carbs is the later model had an extra mid-range port in it that fed directly from the float bowl. If you look at the float bowl, you see an extra hole in it. Inside the throat of the carb, you see an extra mid-range port that is kind of down on the side of the venturi. The 'transition ports" are at the top of the carb as well as the idle port.

Good Luck
Steve

I couldn't find anything about a MSD 2515 ignition system. I would suggest that you contact technical support at MSD.

http://www.msdpowersports.com/Support/

Good Luck
Steve

No ...There is a plunger switch in tranny just replace the s/w or try cleaning it i think its on top front youll see 2 wires going to it ... good luck ';';'

These floats can be tricky to get out. First, you have to remove the gauge if it's in the place where a fuel cap normally goes. I'm not too familiar with the later models. The fuel gauge is held in by a rubber ring. Rock the gauge while pulling on it gently. The wires that connect it to the sending unit are very short and you don't want to pull them loose. The sending unit is held in by four or five small screws. Take them out and work the float arm and float out of the tank. You'll have to be very careful that you don't bend the float arm while trying to get it out and back into the tank. Replace the gasket underneath the sending unit flange. There may be a small pin to assist in the grounding connection of the unit in the gasket, watch for it. If you need a troubleshooting guide, I can send you one for an older bike but the principle is the same. [email protected]

Good Luck
Steve

A website called Motorcycleid.com that offers a variety of parts and accessories for your Harley Davidson, including battery mounts and hardware. I couldn't find the exact size of the bolt that fits the battery box on your 2005 Harley Davidson Lierider. However, you can try contacting Harley Davidson's customer service at 1-800-258-2464 and ask them for the bolt size . They may be able to help you locate the bolt or suggest an alternative

Put key in on position for ten min......then try it

It will be printed on the back of the watch or better still, look on the old battery.

The Harley forums are full of great advice.

sportster valve adjustment

Harley Davidson Forums https://www.hdforums.com > ... > Classic > Ironhead Sep 10, 2012 - Option 2: Adjust on the looser end of the range: Set the adjusting screw to finger tight so that you cannot turn the push rod between forefinger ... Valve Adjustments - Harley Davidson Forums Aug 21, 2007 99 Sportster 883, are valves adjustable? May 11, 2010 Valve Adjustment - Harley Davidson Forums Apr 21, 2008 valve adjustment on TC96? - Harley Davidson Forums Dec 17, 2007 More results from www.hdforums.com ..

'd1ag' for Diagnostic or Service model. To enter the diagnostic system and retrieve a trouble code, hold down the trip reset button while turning the ignition from off to on. This will allow you to cycle through the categories, and see which one indicates a code.Feb 9, 2021

Harley-Davidson Trouble Codes: Everything You Need To Know

just the light says so?"N" will not glow. or both light N and bike will not push roll> are brakes looked up, seized. rolls with clutch pulled in? ive driving vast motor cycle brands, even old harley 45 flat heads. back to 1963 some I have to jog the bike in gear key out ,clutch not touched. to get the gears to free up and find neutral the gear have a thing called dogs. that must un lock also some bikes have lots of switches to make a starter work clutch switch Neutral kick stand. the shifter parts my be a bit rusty