Question about 1995 Ford Escort

1 Answer

Cooling Fan Control

I need to know where the cooling fan control is located. We think this is the problem -- my cooling fan doesn't come on...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

There is a relay in the junction box under the hood if the cooling fan is not coming on when the engine is at 180 degress you can take the a/c clutch relay and switch it with the fan relay. if the fans come on it's the relay if it still doesn't it's the temp sensor on the fan unit....please rate this

Posted on Sep 02, 2008

1 Suggested Answer

  • 50 Answers

SOURCE: Cooling Fan Control

The cooling fan control module is located in front of the radiator. It should have 3 wiring harness's coming off of it.

Posted on Aug 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fan is not working on 2001 Chevy Silverado 2500 truck radiator fan motor?


The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the powertrain control module (PCM) to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the underhood fuse block.
During low speed operation, the PCM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the low speed fan relay coil, closes the relay contacts, and supplies battery positive voltage from the low fan fuse through the cooling fan motor supply voltage circuit to the left cooling fan. The ground path for the left cooling fan is through the cooling fan s/p relay and the right cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. After a 3 second delay, the PCM supplies a ground path for the high speed fan relay and the cooling fan s/p relay through the high speed cooling fan relay control circuit. This energizes the cooling fan s/p relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the high speed fan relay coil is energized closing the relay contacts and provides battery positive voltage from the high fan fuse on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
Your best bet would be to take your vehicle to a qualified repair shop !
Relay Driven Dual Cooling Fan Diagnostics

Aug 19, 2016 | 2001 Chevrolet Silverado 2500

1 Answer

I have a 2003 ford escape my cooling fan is not coming on l suspect is the cooling sensor but I cannot locate it.


The engine cooling fan system is controlled by the on board computer (PCM), there is no separate fan sensor, it is done through the ECT sensor, if that was bad the check engine light should be on. I would think the fan control relays may be at fault here or the fan is just burned out or the connectors are melted, have seen both.

May 29, 2016 | 2003 Ford Escape

1 Answer

I have an 05rendezvous,need to locate switches for cooling system,fans aren't co ming on & now I'm going to need a new radiator,cuz plastic broke.But it broke before fans gave out.Which I changed stat


The engine cooling fan system is controlled by the body control module (BCM) and the powertrain control module (PCM) or engine control module (ECM). The BCM performs the calculations as to how long, when and what speed the cooling fans should turn on. The BCM then sends a class 2 message to the PCM/ECM to engage the cooling fan relays. If there is a malfunction with the BCM, the PCM/ECM will control the engine cooling fans independently. The engine cooling system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the PCM/ECM to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the underhood accessory wiring junction block. The ground path is provided at G100.
During low speed operation, the PCM/ECM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the cooling fan 1 relay coil, closes the relay contacts, and supplies battery positive voltage from the cool fan 1 fuse through the cooling fan motor supply voltage circuit to the left cooling fan. The ground path for the left cooling fan is through the cooling fan 2 relay and the right cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM/ECM supplies the ground path for the cooling fan 1 relay through the low speed cooling fan relay control circuit. After a 3 second delay, the PCM/ECM supplies a ground path for the cooling fan 3 or S/P relay and the cooling fan 2 relay through the high speed cooling fan relay control circuit. This energizes the cooling fan 2 relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the cooling fan 2 relay coil is energized closing the relay contacts and provides battery positive voltage from the cool fan 2 fuse on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
The BCM and PCM/ECM command Low Speed Fans on under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 106?°C (223?°F).


?€¢
A/C refrigerant pressure exceeds 1 310 kPa (190 psi).


?€¢
After the vehicle is shut off if the engine coolant temperature at key-off is greater than 140?°C (284?°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.

The BCM and PCM/ECM command High Speed Fans on under the following conditions:
?€¢
Engine coolant temperature reaches 110?°C (230?°F).


?€¢
A/C refrigerant pressure exceeds 1 655 kPa (240 psi).


?€¢
When certain DTCs set.


The three relays are located in the under hood fuse / relay box ! You need to have it checked for DTC'S -diagnostic trouble codes ! An you need a GM Tech 2 scan tool !
This diagnostic procedure supports the following DTCs:
?€¢
DTC P0480 Cooling Fan 1 Relay Control Circuit


?€¢
DTC P0481 Cooling Fan 2 and 3 or S/P Relay Control Circuit


?€¢
DTC P0691 Cooling Fan 1 Relay Control Circuit Low Voltage


?€¢
DTC P0692 Cooling Fan 1 Relay Control Circuit High Voltage


?€¢
DTC P0693 Cooling Fan 2 and 3 or S/P Relay Control Circuit Low Voltage


?€¢
DTC P0694 Cooling Fan 2 and 3 or S/P Relay Control Circuit High Voltage


  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the Fans Low Speed ON and OFF.
Do the low speed engine cooling fans turn ON and OFF with each command?
Go to Step 3
Go to Step 4

3

Important:: A 3 second delay occurs before the powertrain control module (PCM)/engine control module (ECM) changes the cooling fan speed.
With a scan tool, command the Fans High Speed ON and OFF.
Do the high speed engine cooling fans turn ON and OFF with each command?

Aug 08, 2015 | Cars & Trucks

1 Answer

The location of a 2002 chevy cavalier cooling fan sensor


The cooling fan is controlled by the PCM - powertrain control module through a relay ! There is no cooling fan sensor , there is a coolant temperature sensor ! This coolant temperature sensor is an input to the engine computer , if there were a problem wit the sensor the check engine light would be on .
Cooling Fan Control
The engine cooling fan system consists of one cooling fan and one relay. The relay is powered by the battery positive voltage circuit and controlled by a switched ground from the powertrain control module (PCM).
During operation, the PCM supplies the ground path for the cooling fan relay through the cooling fan relay control circuit. This energizes the cooling fan relay coil, closes the relay contacts, and supplies battery positive voltage from the cooling fan fuse through the cooling fan motor supply voltage circuit to the cooling fan. The cooling fan motor is grounded through its own ground circuit.
The PCM commands the fan on under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 106?°C (223?°F).


?€¢
A/C refrigerant pressure exceeds 1310 kPa (190 psi).


?€¢
A/C is requested and vehicle speed is below 100 km/h (62 mph) with A/C pressure above 1413 kPa (205 psi).


?€¢
Vehicle speed is less than 8 km/h (5 mph) for more than 750 seconds. The fan will turn off when vehicle speed is greater than 8 km/h (5 mph) for more than 20 seconds.

Jun 12, 2015 | 2002 Chevrolet Cavalier

1 Answer

What is the cause of p1660 on nissan pathfiner


Definition of Diagnostic Trouble Code P1660 Acura: A/T-FI Data Line Failure/TCM - ECM Halt Comprehensive Buick: Cooling Fan Control Circuits Cadillac: Cooling Fan Control Circuits Chevrolet: Cooling Fan Control Circuits GMC: Cooling Fan Control Circuits Honda: A/T-FI Data Line Failure/TCM - ECM Halt Comprehensive Oldsmobile: Cooling Fan Control Circuits Pontiac: Cooling Fan Control Circuits Saturn: Cooling Fan Control Circuits

Mar 16, 2015 | Nissan Pathfinder Cars & Trucks

1 Answer

Fusebox location


Relay Center Cooling Fan Controller
  • Located behind the left side of the instrument panel.
Cooling Fan Controller Module
  • Located behind the right side of the instrument panel.
Cooling Fan Relay
  • Located in the air conditioning cooling fan control module.
Electronic Control Assembly
  • Located under the left side of the instrument panel.
Electronic Engine Control Power Relay
  • Located behind the glove box on the right side of the instrument panel.
Fuel Pump Relay
  • Located behind the glove box.
Horn Relay
  • Located in the fuse block.
Let me know if this helps. If not, let me know.

Circuit Protection The fuse panel is located below and to the left of the steering column.
Fuses are a one-time circuit protection. If a circuit is overloaded or shorts, the fuse will blow thus protecting the circuit. A fuse will continue to blow until the circuit is repaired.

Main fuse box located on driver's side to the left of the steering wheel, above the brake pedal.


bc445f7.gif

Aug 07, 2010 | 1991 Ford Tempo 4 Door

1 Answer

Code p1652 on a 1996 pontiac grand prix does anyone know what it means the book for computer codes is incomplete


Trouble code P1652 means: Cooling Fan 2 Relay Control Circuit Malfunction

I would start by checking power supply to the cooling fans,making sure the coolant system is full,& using a scn tool to verify the proper operation of the cooling fan system.Here is some info to help you.

The Powertrain Control Module (PCM) controls the operation of the cooling fans. This is accomplished by providing a ground path for the cooling fan relay coils within the PCM. The relay contacts will close and complete the circuit between the fusible link at the battery junction block and the fan motors. Whenever there is a fan ON request both fans will be running.

Power for the fan motors is supplied through a fusible link at the battery junction block. Battery positive voltage is applied to the cooling fan relay contacts and coils. The cooling fan relays are energized when current flows through the relay coils to ground at the PCM. The cooling fan relay #1 control circuit is used for low speed cooling fan operation. The cooling fan relay #1 control circuit and the cooling fan relay #2 and #3 control circuit are both grounded for high speed fan operation. The cooling fan relay control circuits are monitored by the PCM. Before using the Electric Cooling Fans diagnostic tables be sure to perform the Powertrain On-Board Diagnostic System Check. If diagnostic trouble codes P1651 or P1652 are present, use the appropriate DTC diagnostic tables prior to performing Electric Cooling Fans diagnostics.

Important:
When certain Diagnostic Trouble Codes (DTCs) are present, the PCM may command the cooling fans to run all the time. It is important to perform the Powertrain On-Board Diagnostic System check prior to diagnosing the engine cooling fans.The PCM will complete the ground path for cooling fan relay #1 under any of the following conditions:
- When engine coolant temperature exceeds 105°C (221°F)
- When A/C is requested and ambient temperature is greater than 10°C (50°F)
- When A/C refrigerant pressure is greater than 190 psi (2 volts)

For high speed cooling fans operation, the PCM will delay control of the cooling fan #2 and #3 relays for 6 seconds. The 6 second delay ensures that the cooling fan electrical load will not exceed the capacity of the system. The PCM will complete the ground paths for cooling fan relays #1, #2, and #3 under any of the following conditions:
- When engine coolant temperature exceeds 113°C (235°F)
- When A/C refrigerant pressure is greater than 275 psi (2.9 volts)

If a problem that involves the low speed cooling fan relay control circuit (cooling fan relay #1 control) exists, DTC P1651 should set. If the problem affects the high speed cooling fan relay control circuit (cooling fan relay #2 and #3 control), DTC P1652 should set. A problem with the ECT sensor should set DTC P0117, P0118, P1114, or P1115. Any of these DTCs will affect cooling fan operation and should be diagnosed before using the Electric Cooling Fan Diagnosis table. The Electric Cooling Fan Diagnosis table should be used to diagnose the PCM controlled cooling fans only if no DTC is set.
Hope this help to solve your poblem (remember rated and comment this help).

Mar 21, 2010 | 1996 Pontiac Grand Prix

1 Answer

Where is the fuse box panel for a 1993 ford tempo


Access the fuse panel from the left of the steering column Relay Center Cooling Fan Controller
  • Located behind the left side of the instrument panel.
Cooling Fan Controller Module
  • Located behind the right side of the instrument panel.
Cooling Fan Relay
  • Located in the air conditioning cooling fan control module.
Electronic Control Assembly
  • Located under the left side of the instrument panel.
Electronic Engine Control Power Relay
  • Located behind the glove box on the right side of the instrument panel.
Fuel Pump Relay
  • Located behind the glove box.
Horn Relay
  • Located in the fuse block.

Oct 13, 2009 | 1993 Ford Tempo

1 Answer

Where are the cooling fan relays for a 1998 Cadillac Deville Northstar located?


Are you sure that you don't mean the cooling fan control module? It should be located up front next to the cooling fan. It is square shaped and has a long square shaped plug going into it. 00114_cooling_fan_control.jpgReads the temperature of the coolant and passes the information to the engine control computer (ECC). The ECC receives analog information and signals the cooling fan switch to cycle the cooling fan on or off, as required.








Jul 07, 2009 | 1998 Cadillac DeVille

1 Answer

Cooling Fan Control


The cooling fan control module is located in front of the radiator. It should have 3 wiring harness's coming off of it.

Aug 21, 2008 | 2004 Mazda 6

Not finding what you are looking for?
1995 Ford Escort Logo

687 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...