Question about 1997 Toyota Camry

5 Answers

Cv joint I cant seem to get the inner to come out of the tranny, have tried prying and pulling to no avail. '97 camry, any suggestions?

Posted by on

  • KMitch76 Sep 27, 2008

    My axle came apart know I cannot get the inner part out of the Trans.

×

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

They do make a tool for removing these inner C.V. joints, it is avalible at Car Quest Auto Parts.

Posted on Nov 25, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The problem is the joint has come loose from the inner housing and I can not get a slide hammer on it. This is the driver side. Went to remove the passenger side so I could get a punch and try to knock it out but it also came apart and I cannot get it out know. If anyone has any ideas it would be greatly appreciated. E-Mail address is kevin.mitchell@voith.com Need info really bad. Thanks.

Posted on Oct 15, 2008

Give up its impossible

Posted on Sep 25, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 169 Answers

The joint is held in with a spring clip. Try a brass punch and a hammer. Hit it on the metal part of the joint,forcing it away from the transmission.Be careful not to hit it too hard, or slip off and hit the boot.Spray the shaft into the trans with WD40 or an equivalent.Good Luck.

Posted on Sep 01, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Is it on the driver side or the passenger side? when i have a little trouble i use a slide hammer. put the nut on the shaft and use the 3 jaw attachment of a slide hammer this will help you.

Posted on Sep 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pulling a cv axle from a 97 toyota rav4


mark the relationship of the inner cv joint to the flange.place a large screw driver between wheel studs hold driveaxle and remove the inner cv joint to axleshaft flange nuts remove the freewheel hub remove the driveaxle snap ring and spacer pull the inner cv joint off the axleshaft flange studs lower the inner cv joint and pull the driveaxle assembly out of the steering knuckle.let me know if this helps.

Jan 24, 2012 | Toyota RAV4 Cars & Trucks

1 Answer

Trying to pull gearbox out but cant figer out how cvs come out


IF YOU CANT TAKE A PRY BAR AND PRY THE INNER CV JOINT.CHECK CV JOINT YOU PROBABLY HAS 3 BOLTS HOLDING DRIVE AXLE IN PLACE.

Jun 12, 2011 | 1992 Nissan Sentra 4 Door

1 Answer

1993 Ford Festiva GL cv axle broke off in tranny. Need advice on how to remove safely without damaging tranny.


Use a prybar to separate the halfshaft from the transaxle. Is the inner cv joint still attached, so you can pry against it?

May 24, 2011 | 1993 Ford Festiva

1 Answer

Im trying to replace the driver side cv. the inner boot came off with the whole drive axcel, except for the inner spine. it looks lkike the previous owner removed the inner cv joint and replaced the boot...


YOU HAVE TO REMOVE WHOLE AXLE AN INSTALL AXLE IN INNER CV JIONT THEN MAKE SURE IT CLIPS IN,INSTALL BOOT AN RECLAMP CV BOOT WITH SPECIALLTY PLIERS

Dec 21, 2010 | Mazda 323 Cars & Trucks

1 Answer

I cannot get the cv joint out. how is the inner joint disassembled. I pulled on the joint and the joint extended and now will not go back in. I am assuming I can disconnect the inner join so I can...


Ok to get the inner joint out you need to stick a pry bar in between the transmission and the inner cv joint. When you pulled the joint to remove the axle the bearing in the joint came out of position. You can put it back by pushing it into place.
nvannoy.jpg

Dec 15, 2010 | 2003 Toyota Corolla

1 Answer

How to replace cv axels in 1986 pontiac grand am 3.0 litre


much easier to do this on a lift. You have to break the lower ball joint loose (and in some cars the tie rod end too), remove the axel nut, pry the a-frame down with a big pry bar between the aframe and car frame or inner fender skirt. While one person prys a-frame, the other person pulls the hub away from the car to clear the lower ball joint. Pull the axle out of the hub first, then straight out of the tranny. Use a drip pan under the tranny in case it leaks a little. Push the new axle straight into the tranny until it clicks in. put the other end into the hub and have someone pry the a-frame down again while you get the hub back into the ball joint. button her back up...

Sep 04, 2010 | 1986 Pontiac Grand Am

1 Answer

Inner cv joint removal 98 escort


what you are doing is right but on the rare occasion that you get one that is tight you need a good sturdy jemmy bar and a good smack with a lump hammer

May 11, 2009 | 1995 Ford Escort

3 Answers

Cannot get the CV joint Driver side to pry out of the transaxle


take a pry bar between cv and tranny if this is possible and pry out. the c clip on inner shaft is stuck in tranny. common issue.

Apr 15, 2009 | 2002 Mazda 626

1 Answer

Trying to get the bearing off of the cv axle 1994 camry


I think you mean cv joint. If so, a new axle cost $59. You are doing alot of extra work and the joints could be damaged. The outer joint comes off, but it takes a large hammer. The inner joint usually has an inboard ring clip that you pop out with a screwdriver.

Mar 25, 2009 | 1994 Toyota Camry

1 Answer

Inner cv joint disassembly


If you are changing the CV joint with shaft, after getting the outer end of the shaft out of the hub, Take a small pry-bar and pry the shaft out of the tranny.

Mar 14, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
1997 Toyota Camry Logo

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...