Question about 2002 Ford F250 Super Duty SuperCab

1 Answer

Door Locks I had to replace my batteries on my 250 diesel. Now the electronic door locks will not work. slight clicking sound when button pressed or remote pressed but doors will not lock.

Posted by on

  • dlemmons Sep 06, 2008

    I have the same problem with the doors making an unlocking and locking sound and a clicking underneath the dash. I thought it might be a relay. I went to AutoZone and purchased a relay but cannot find where it goes. I read online that it might be located in the left "C" pillar. Where is the left "C" pillar. Thanks!

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 169 Answers

Sounds like you have an electric lock actuator going bad. It only takes one and they all act up.The vehicle security module and the switches share the same ground. It is ground #900. Located on the left C pillar. Check to see if the ground is clean and tight. You can disconnect one actuator at a time. If you disconnect the bad one, the rest will function.Did you have any doors making a loud grinding noise when the locks were applied?if yes, start with that one. If no, start with the drivers door.The drivers lock actuator sees more work than the rest since it unlocks by itself on the first push of the remote.If this is something you do not want to do,try the find a repairman option at the bottom of the page. If you need more help,don't hesitate to drop a line.Good Luck

Posted on Sep 01, 2008

  • Tom Wolff
    Tom Wolff Mar 30, 2011

    AutoDoc ---- can you give a little more specific info on where ground #900 is on the C pillar and how to go about locating it. 3 of my doors never unlock/lock --- driver, rt front and rt rear --- lt rear will sometimes. Any more specifics you could give would be greatly appreciated. Thanks, Tom

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why don't power locks work?


it maybe the BCM may have a problem or needs to be reset.

Sep 06, 2015 | 2010 Chevrolet Chevrolet Malibu LT

1 Answer

How to reset door locks grand vitara 2009


what locks, on what doors,
the FOB buttons, the door actual buttons. what?

do say? what was before.?
on my cars, the door locks are programmable.

what did the do before.
and then after.

on mine , i can control what the doors do
i can use 1 click to open all doors, or double clicks and other things.
even driver door only click opens only driver door.
is the fob totally dead.
are the manual locks working? on each door.?

Apr 11, 2014 | Suzuki Grand Vitara Cars & Trucks

1 Answer

Xj8 door lock


You need to replace the lock actuator in the doors that are not locking/unlocking with the door switch/remote. If the remote works for most of the doors then it is fine. The actuator is what moves the lock when it gets the signal from the remote or door switch to move it.
Good luck

Jul 11, 2013 | Cars & Trucks

1 Answer

Power lock


check door locks fuses and relays.if all is good and you cant operate door lock buttons manually problem could be in the generic electronic module.if door locks dont work from the remote battery could be dead in remote transmitter.try to reset door locks control module first obtain all remote transmitter.sit inside vechicle with all doors closed.switch ignition from off to on 8 times in 10 seconds. doors should lock then unlock.when this procedure works then press any button on any of the remote transmitter doors should lock and unlock.if all fails let dealership fix..

Dec 27, 2012 | 1998 Ford Windstar

1 Answer

I have a 2000 ford mustang. Suddenly my keyless entry remote stopped working. I replaced the battery and turned the off and on 8 times and the locks cycled. after which i pushed the unlock but nothing...


The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:
  • generic electronic module (GEM)(14B204)
  • keyless entry remote transmitter (15K601)
  • NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
    Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
    Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
    • The doors do not lock/unlock using the remote transmitter
    • Ignition switch.
    • GEM.
    • Remote transmitter.
    • Remote transmitter batteries.
    • GO to Pinpoint Test C .
    You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
    1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
    1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
      Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
    1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
    1. Take an have the vehicle checked for DTC'S
B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM

Apr 12, 2017 | Ford Mustang Cars & Trucks

2 Answers

New battery and altternator and now automatic key does not work or radio


you shaould find instructions in the owners manual, otherwis its back to the dealer

Jul 27, 2010 | 1999 Ford Escort

1 Answer

My power door locks stopped working. When I press


The locks don't work from any switch or just the driver's door switch ? The door locks are controlled by the BCM - body control module , that's were the clicking you hear is coming from there are no fuse's that are marked for the locks , fuse's for the BCM .

Door Lock System Components
The power door lock system consists of the following components:
• Driver door lock switch -- Uses a single signal wire for both lock and unlock switch activations
• Front passenger door lock switch -- Uses a single signal wire for both lock and unlock switch activations
• BCM -- Class 2 module which requires programming when replaced
• Reversible door lock actuators in each of the doors
• BCM PWR 15A fuse -- Located in the BCM fuse panel, supplies power for the door lock system

The BCM PWR fuse supplies battery positive voltage to the BCM for the door lock system.
The BCM supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position, the reference voltage is taken directly to ground and the BCM senses 0.0 volts on the signal circuit. If a door lock switch is placed in the unlock position, the reference voltage is taken to ground through a 15k ohm resister that is internal to the door lock switches and senses approximately 2.9 volts on the signal circuit. This is how the BCM determines what portion of the door lock switch was activated.
The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately.
Vehicles without keyless entry have two internal drivers in the BCM to control the door lock actuators. All door lock and all door unlock. Vehicles equipped with keyless entry have three internal drivers in the BCM. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked by itself using the keyless entry transmitter.

Body Control Module (BCM)
Lower center of the I/P, just below the HVAC control assembly

Mar 04, 2018 | 2004 Saturn ION

1 Answer

My 05 Equinox drivers electronic door lock doesn't work with the remote only locks/unlocks with the key. All the other door locks work.


YOUR REMOTE BATTERY NEEDS REPLACING.TAKE IT TO DEALERSHIP.THEY WILL REPLACE REMOTE ENTRY BATTERIES AND REPROGRAM THE DOOR LOCKS.

Jan 18, 2010 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Audi A3 2004 remote opens door then it locks straight away


drivers door lock needs replacing,if you have the central electronics checked it will give you a code,and i will possibley be that door,the microswitches play up in them quite a common fault

Feb 14, 2009 | 2005 Audi A3

Not finding what you are looking for?
2002 Ford F250 Super Duty SuperCab Logo

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...