Question about 2001 Acura 3.2TL
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.
btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.
Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.
If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.
If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)
Posted on Jan 05, 2009
it is at the rear bottom of engine, points inside the bell housing of the transmission, u will need to jack the car off the ground to see it and get at it for repAIR
Posted on Feb 28, 2009
This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.
Posted on Mar 19, 2009
grantgga2: I don't think this is one you are going to want to try to change out.
It entails having to remove the left axle and part of the exhaust pipe to gain access to the starter. At that point, you have one bolt which goes in at the bottom from the starter side and bolts to the engine. The other bolt passes through the trans axle housing and bolts into the starter, pulling it up to the engine.
SCARED YA HUH? I'D SAY FROM A 1-10 FOR A WEEK END WARRIOR, IT WOULD BE ABOUT A 6.
Was I helpful?
Posted on May 03, 2009
Tips for a great answer:
Jul 22, 2016 | Acura Cars & Trucks
Jan 08, 2016 | 1998 Acura CL
Nov 04, 2015 | Honda Cars & Trucks
Sep 10, 2015 | Acura Cars & Trucks
Sep 05, 2015 | Acura Cars & Trucks
Apr 14, 2010 | 1998 Acura TL
Feb 28, 2009 | 1996 Acura TL Series
317 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: