Question about 1994 Ford Crown Victoria

1 Answer

1994 Crown vic. Lx

Hi everyone i have and issue with my front calipars. they rattle the breaks in them are new and when driving you hear a rattle and i took the wheels off in the front and they seem loose but cant figure out how to tighten them up. or do i have to get new ones. the Anit Break light is on as well can this be the problem as well? thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Hi , you can check if the calipers are working properly , if they start getting bad, they dont open and close the way they should and this can cause the rattleling noise, lift the front of car and secure it in jack stands ,have some one to apply and release the brakes while you turn the weel,check how fast the tire stops and release .it shold stop and release instantly,

Posted on Sep 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 05 Crown Vic LX is misfiring Cylinder 1 2 and 3.


Your next step would be to check for injector pulse (signal at injector) and are the injectors working. Is the miss while driving, at idle, under load, or decell? What codes are u getting?

Oct 22, 2014 | 2005 Ford Crown Victoria

1 Answer

Timing chain


You need to replace the timing chain guides/tensioners. 200-2003 crown vics are prone to that problem. 2004 and up are all okay (with new modified design.)

Feb 15, 2014 | 2001 Ford Crown Victoria

1 Answer

'99 Ford Crown Vic LX: #12 30A Maxi fuse blows seconds after starting or ignition turned on.


i had this problem with my 1999 jeep grand cherokee laredo with the brake lights it kept popping fuses right after the ignition was turned on try putting a higher amp fuse in place of the old one that keeps blowing then check for shorts to the starter and check grounds and wires and also the transmission issue check the fluid and then if the fluid is fine change the transmission filter the filter may have not gotten replaced when the transmission was rebuilt and may be clogged or dirty

Oct 04, 2012 | 2002 Ford Crown Victoria

1 Answer

How to take rear inside door panel off 94 ford crown vic lx


michael_cass_313.jpg
Hope this helps you ?? ps. would have made picture bigger, but this web page won't allow it....

Jul 14, 2011 | 1994 Ford Crown Victoria

1 Answer

1994 ford crown vic front pass. side power window regulator...


Yes it is. They will need to be drilled out. Thats the best way, some people try to put bolts on, but I dont advise it.

May 12, 2010 | 1994 Ford Crown Victoria

2 Answers

Where is the a/c charging valve on a 2000 crown vic lx


low pressure line under the engine on the passenger side by the compressor. U must get under the car to access it

Apr 06, 2010 | 2007 Ford Crown Victoria LX Sedan

1 Answer

1988 Ford Crown Vic Strange Idle (Getting Worse)


i am trying to install an aftermarket temperature guage with capillary tube into my 1988 crown victoria ltd 5.0 efi. where does the capillary tube mount?

Jun 27, 2009 | 1988 Ford Crown Victoria

3 Answers

94 crown vic driver power window does not work can


The window regulator can be broke. Its made of plastic and they break often.

May 03, 2009 | 1994 Ford Crown Victoria

Not finding what you are looking for?
1994 Ford Crown Victoria Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...