Question about 1999 Ford Super Duty F 450

1 Answer

Oil pan how do i remove to repair it leaks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

You have to raise the car if you can go to a lifter, or the hard way is to use aligator jacks, lift it as high as you can, use jack stands for safety, go underneath the engine, ( be sure the car is safe to go underneath)

drain the oil by removing the oil plug in the pan,
remove all bolts surrounding the oil pan,
gently remove the oil pan and take note not to tear the old pan gasket.( If you already have a new gasket then its ok to damage it)
do the repair on the pan as you wish,
then do the reverse on installing.

if you will use the old gasket, may i suggest that you use silicone gasket to further seal the pan and prevent oil leakage.

tnx 4 using fixya,

drcool

Posted on Sep 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I change my 3.0 Liter oil pan gasket


Hi, Im AL the owner of Big As Auto Repair.

I actually own a 1995 Dodge Spirit 3.0 and its not to difficult. The hardest part is removing the bracket on the transmission so you can remove the dust cover for the flywheel. (1) Drain the oil. (2) Remove the transmission bracket and the dust cover. (3) Remover all the pan bolts except one, just loosen this one so you can pry the pan off, because the pan will be stuck on. (4) Clean the engine block and the oil pan very clean. (5) Install the gasket OR sealer which ever it calls for and install the pan and fill with new oil and filter. Hope this helps and please visit my Auto-Repair-Website: http://www.bigasautorepair.com/

Apr 25, 2014 | 1994 Dodge Spirit

2 Answers

Replace gasket, oil leak front of oil pan and timing chain cover


Yes, oil commonly leaks from its valve cover gasket the only way to fix this problem is buy replacing the gaskets. -----------------------------------------------------------------------------------
car cables & obd conectors

Dec 24, 2012 | 1993 Geo Tracker

3 Answers

Need to replace oil pan gasket for 1996 Ford F-150 2wd, I-6


Yes you can do it yourself.
Its not very easy,but with basic Auto repair tools the task can be easily completed.

=========
There are few help links with solutions to complete these task.
I suggest you to refer these links and view its procedure.

-------
Click the link below:----
------------
How to Replace an Oil Pan Gasket?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html
-----------

KIA Sportage leaking oil from oil pan?

Go to Newly Launched

FREE Car repair gu
obyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html" http://howtobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html
----------------
Oil pan Gasket on 1998
Toyota Tercel?
http://howtobyme.blogspot.com/2011/11/oil-pan-gasket-on-1998-toyota-tercel.html

-------------
VALVE COVER GASKET REMOVAL GUIDE http://technoanswers.blogspot.in/2012/06/valve-cover-gasket-removal-guide.html
--------- Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

------------
How to replace Oil Pan on 2008 Honda Odyssey?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pan-on-2008-honda.html

-----------
How to replace Oil Pressure Sensor on 2008 Honda Odyssey?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pressure-sensor-on.html

------------
2004 Chevrolet Express Van: Oil pressure sending unit replacing? http://whoisbyme.blogspot.in/2012/06/2004-chevrolet-express-van-oil-pressure.html
-------------
HOW TO REPLACE AN OIL PUMP
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html
-------------
HOW TO CHANGE ENGINE OIL AND FILTER
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html
--------------
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html


-------------

How to Check Differential Oil Leaks and Replace Oil
http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html
-----------
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

----------
HOW TO RESET OIL CHANGE INDICATOR? http://whoisbyme.blogspot.in/2012/07/how-to-reset-oil-change-indicator.html

------------
These details will help.
Thanks.

Nov 25, 2012 | Cars & Trucks

2 Answers

When changing the oil pan on a 2006 town & country do you have tighten the bolts in a sequence?



Removal & Installation

2.4L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.

To install:
  1. Install or connect the following:

    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.

To install:
  1. Install or connect the following:

    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    0996b43f8020961b.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Oil pan mounting bolt tightening sequence-3.0L engine


To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:

    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:

    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

May 05, 2012 | 2006 Chrysler Town & Country

1 Answer

I own a 1998 deville that has 120,328 miles of which 664.6 are my driven miles. I was told when I purchased that it had a small oil leak. I got an oil change about 6 weeks +/- a week, after which i noticed...


Hello: There isn't any temporary repair. It is a major task to seal the oil leak, the engine has a two piece oil pan. To remove the oil pan either the transmission or engine has to be removed to accomplish the task.

Aug 25, 2011 | 1998 Cadillac DeVille

2 Answers

I have an oil pan lead in my 2006 dts, how to fix?


I assume you mean an oil pan LEAK. If so either the pan has a hole in it or the gasket is leaking. Either way the pan will have to be removed to repair the hole of replace the gasket. If it is the gasket that is leaking try tightening the oil pan bolts to 10 ft/lbs of torque.

Jul 28, 2011 | 2006 Cadillac CTS

1 Answer

Oil pan is leaking really bad


If it is leaking at the gasket, remove and replace the gasket.
If it is leaking at a corner from a rust spot, you may be able to repair it if the hole is small with Puddy Epoxy, that sets in 5 minutes and cures in 1 hour or so.

I tried this on a 1998 Ford Taurus that had a difficult to remove oil pan that seemed to drip oil when shut off.

I got a screwdriver and poked a larger hole in the oil pan and made the edges go ragged around the hole.

Then, I sprayed it with brake cleaner to get the oil residue off.
Then, I got a golf ball sized amount of Puddy Epoxy, mixed it by kneeding it in my two hands, then I applied it to the hole. It works great, going on 2 years.

A lot cheaper than a new pan removed and replaced, by the way.

Good luck on this repair.

Oct 15, 2010 | Dodge Stratus Cars & Trucks

1 Answer

How to change oil pan gasket for 2005 dodge caravan


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004

Oil Pan - Removal & Installation

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.
To install:
  1. Install or connect the following:
    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    e6c7cfd.jpg
    Fig. Oil pan mounting bolt tightening sequence-3.0L engine

To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:
    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:
    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

Hope helps (remember rated this).

Jun 24, 2010 | 2005 Dodge Caravan

1 Answer

I have a leak in the body of the oil pan on my 2004 chevy suburban 2 wheel drive. It is a hairline crack. Do I have to remove the entire engine to install a new oil pan? Can the frame cross member be...


YOU NEED A REPAIR MANUAL BECAUSE YOU HAVE A FEW THINGS YOU HAVE TO DO TO REMOVE OIL PAN.FIRST OF ALL YOU HAVE LOWER FRONT DIFFERENTIAL CARRIER WITH FLOOR JACK IF YOU HAVE 4WD VECHICLE..DISCONNECT THE FRONT EXHAUST Y PIPE FROM THE ENGINE AND THE EXHAUST SYSTEM.YOU HAVE TO REMOVE OIL PAN SKID PLATE.AND THE LOWER CONTROL ARM CROSS MEMBER FROM BELOW THE OIL PAN.

May 05, 2010 | 2004 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...