Question about 2002 Mazda Protege

1 Answer

2002 Mazda Protege 5 Hub Bearing Replacement

Need to know how to get the hub off the vehicle to replace the hub bearing. I had taken it apart twice but haven't been able to get it off and replaced.

Mel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Which hub the rear or front?

Posted on Sep 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheel bearing retaining ring..


Unless you know how to fix this failure I would suggest that you have it taken to a reputable shop and have the bearings investigated as it may also include a hub as well. CV joints seldom come apart unless the whole wheel and hub falls off so I would be in favour of a hub damage and wheel bearings.

Feb 22, 2014 | Cars & Trucks

Tip

Mazda 323/Protege front wheel bearing


The moment you can hear a loud noise coming from front wheels while driving straight that means that your wheel bearings are ready for replacement. In a Mazda 323 BJ (1999-2004) it usually comes every 150-200 thousand kilometers (95-120k miles). To replace the bearing (do two of them in one go even if only one can be heard) you need to do as follows:
Loosen the nut on the half shaft, jack up the car, remove the wheel, dismantle brake caliper and brake disc, remove all ball joints attached to the hub, detach the shock absorber from the hub (no need of removing it completely), once you have the hub basically hanging on the half shaft, untie the nut and pull the hub out of the shaft so you can hold it in your hands. You will need to go to a garage with a 12ton (minimum) press, no point of trying to hammer the bearing out as you may damage the hub and your whole work will be for nothing. Get the old bearing pressed out and the new one pressed in.The Mazda part numbers for the front bearing kit are: B455-33-047A(B,D),GJ21-33-042B,G304-33-065,B21M-33-048.
After getting the bearing fitted into the hub, all we need is to reverse the whole process, put the shaft into the hub, attached the hub to the shock absorber (makes it easier to attach the rest), put the nut and tight it just as much to feel there is nearly no movement (do not overtight it as this might damage the bearing), attach all ball joints back to the hub. Make sure all nuts are tight, use a
tension wrench when needed, put the brake disc back on the hub, install the brake caliper, once you have all them on and tight put on the wheel, then get someone to press the brake while you tight the shaft nut with the tension wrench, check the wheel for play or hard movement. Lower the car down and take a slow drive around (do not accelerate sharply or brake rapidly, just a gentle drive around. Normally a wheel bearing should be in correct position and use after about 200km (120 miles) distance. After that check if it is not overheating (too tight) or there is a play (too loose). Tight or untight if necessary, recheck after same 200km (120 miles).

on Apr 24, 2010 | Mazda 323 Cars & Trucks

1 Answer

Wheel bearing replacement


You go to --- You Tube Video

Then put in your question or
replacing wheel hub bearing assy on 2002
chevy impala

Any vehicle you find will be similar

Remove the axle nut & four bolts behind the
steering knuckle holding the hub on

Feb 15, 2013 | 2002 Chevrolet Impala

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

1 Answer

Rear wheel bearing is in need of replacing on my 91 Mazda Protege, Howv do I do it


That is a whole hub assembly

Remove the wheel, unbolt the center of the hub, pull old hub off, and slide new one on....its real simple

Aug 27, 2009 | 1991 Mazda Protege

2 Answers

Replace rear wheel bearing 2002 ford explorer 4x4


you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful

Aug 15, 2009 | 2002 Ford Explorer

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

560 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...