Question about 2005 Honda CR-V

1 Answer

Tail / brake light lens replacement

How can I replace broken driver's side tailight assembly on 2005 CRV?

Posted by on

  • Coss May 11, 2010

    Are you asking how to do the job? Or where to find the replacement parts?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 421 Answers

Remove the inner plastics on that side and uplug and remove the 10-15 ten mm bolts remove the light and reinstall there maybe some weatherseal holding the light also just yank it out please rate -jeff

Posted on Sep 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When I turn my lights on my tail lights work but when I hit my brakes the don't light up I have a 2001 vw beetle????


the brake lights don't light up or the taillights don't light up? the brake lights are brighter than the tailights so the tailights won't show up whenbrakes are applied. if no lights work when brakes are applied then check for a bad ground at the light assembly.

Jun 14, 2012 | 2001 Volkswagen Beetle

1 Answer

How do you replace the driver's side tail light on


You will first have to access the trunk and then access the tailight assembly - possibly by removing the upholstery of the molding (not too difficult). The bulb housing can be removed by rotating approximately 90-degrees counterclockwise and pulling the assembly. Simply pull the bulb straight out and insert the new bulb. Be sure to test it before reassembling the unit. Finally, reverse the steps.

Feb 11, 2012 | 2006 Mitsubishi Lancer

1 Answer

Need to replace tail lights on 1993 mercury capi


Pretty basic stuff...open the trunk and move the trunk liner material away from the rear of the car to expose wiring for the tail lights...there are 3 light bulbs per side, the backup, brakes and tail lights...just twist the plug where it connects to the lens assembly and the socket will come out...remove the bulb and take it to the auto parts store to make sure you purchase the correct replacement...if your lenses are broken, there are 6 nuts to remove that lets the entire lens assembly be removed and replaced with one from a junk yard, you cannot buy these new anymore...good luck...

Mar 19, 2011 | 1991 Mercury Capri

1 Answer

Need to know how to replace rear passenger tail light lens


Wouldn't it be simpler to just get a used tail lamp assembly on ebay? Most likely any SL tailight assembly 96 to 99 will fit and there are lots of them for sale.

Nov 11, 2010 | 1997 Saturn SL

1 Answer

I have a 2002 Chevy Express van. All of the tail lights work except the driver side. Left signal light and backup light works fine. Problem: The driver side brake light works as long as the running...


The printed circuit board that the bulbs push into needs replacement. Any autoparts store will have it. It just screws into tailight assembly & attaches to wiring harness.

Nov 01, 2010 | 2002 Chevrolet Express

2 Answers

How do u change 2005 sante fe drivers side tailight


Made a video of me changing the brake light but I show how to take out and install the tail light assembly. My video shows passenger side but it should be the same as drivers.

Apr 14, 2010 | 2005 Hyundai Santa Fe

1 Answer

My 2005 Tacoma was hit in the rear and since then not rear lights


You did right so far. Once you have lowered the tailgate and removed the upper and lower 10mm bolts the tail light assembly should be loose and moving a little bit. There are only 2 push-in plastic posts holding it at this point now. Then you have to pull back the assembly firmly, hit on the external side of the assembly with the palm of your hand and it will pop out. DO NOT try to pry with a screwdriver or any other tools.

Disconnect wires connections, replace burned or broken bulbs, make test. If it doesn't work check if the wiring has been affected by the accident.

Hope it will help
Dan

Dec 19, 2009 | 2005 Toyota Tacoma

1 Answer

Only one tailight works. replaced bulb. brake lights work turn signals work driver side tailight works no tailight on passenger side.


i think you'll find with a test light at the tail light connector,that the you do have power but the problem is the unit that holds the bulbs and is a printed circuit is bad

Dec 07, 2009 | 2000 Chevrolet Silverado

2 Answers

Divers brake light does not work with head lights on .


big problem with jeeps 98 and up should be a safety recall but is not; you need to replace the drivers side tail light assembly with a new one, from jeep or auto parts store if available. used auto parts recycler may have one but your taking a chance, used should be 40 to50
dollars new over 100

Sep 16, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Honda CR-V Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...