Cylinder head bolt specs and secquence on chevy caliver 1996 2.2 l

list of trq specs ' Chevy Impala SS Forum

https://www.impalassforum.com > threads > list-of-trq-s...

Nov. 1, 2009 - If you need the head bolt specs, etc, look on this page: ... Cylinder head torque in the '95 states 3 passes building up to 65 ftlbs. Don't have the ...
Head bolt torque
Feb. 23, 2002
Torque Specs
Nov. 3, 2019
Head Bolt Helllppppp!
Apr. 3, 2010
Head Torque Specs
Nov. 3, 2019
More results from www.impalassforum.com

Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Here's a link to your head bolt torque. Repair Guides Engine Mechanical Components Cylinder Head AutoZone com

Go to autozone.com and become a member of their web-site. It is FREE. You can then access repair info for your vehicle. There are repair manuals that show pictures and everything. I will look for your torque specs and picture.

Clean the cylinder head bolts, apply sealer to the threads, and hand-tighten.

Tighten the cylinder head bolts:

1. M11 cylinder head bolts first pass in sequence to 30 Nm (22 ft. lbs.).
2. M11 cylinder head bolts second pass in sequence + 90 degrees.
3. M11 cylinder head bolts (1,2,3,4,5,6,7,8) + 90 degrees
4. M11 cylinder head bolts (9 and 10) + 50 degrees
5. M8 cylinder head bolts (11,12,13,14,15) to 30 Nm (22 ft. lbs.). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
   NOTE The cylinder head gasket displacement can be verified by markings visible on the underside of the right gasket locating tab. Some 4.8/5.3L head gaskets may have 53 stamped onto the locating tab. Some 6.0L head gaskets may have 60 stamped onto the locating tab.

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

DO NOT use any sealing material.


1. Install the cylinder head gasket.
2. Install the cylinder head.
3. Install NEW cylinder head bolts.

Caution!Refer to Fastener Notice in Cautions and Notices.


Click to Enlarge


4. Install and tighten the cylinder head bolts in the sequence shown.

Tighten
Tighten the bolts to 30 N•m (22 lb ft) plus an additional 155 degrees using the J 45059 .


Click to Enlarge


5. Install the NEW front cylinder head bolts.

Tighten
Tighten the bolts to 35 N•m (26 lb ft).

/f

Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.

Use a torque angle meter to rotate each cylinder head bolt 120 degrees in sequence.

Use a torque angle meter to rotate the four center cylinder head bolts an additional 30 degrees in sequence...

I hope this helps.

For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.