Question about 2003 Nissan Altima

1 Answer

Doors lock, windows roll down, and hazards flash on their own.

All of this happening on it's own and keys are out of ignition. Continually getting worse and replaced 2 batteries since June. Please help!!!

Posted by on

  • 2 more comments 
  • Anonymous Jan 05, 2009

    I have the same issue I thought it was cased by the after market alarm, now I'm not so sure.

  • kosta1950 Feb 01, 2009

    Altima 2003 engine 2.5

    Yes I have the same problem

    both front windows roll down when I take off the key from the engine and I open the door to exit

    what is the solution??

  • labtronique Mar 06, 2009

    Hi, I have the same problem until 1 month, my windows roll down when I open the door 1 time per week. But this morning my windows roll down lonely this night.

  • sund45 Apr 22, 2009

    Same thing... my windows roll down when I turn off the car and remove the key. Also my door locks constantly unlock themselves.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

You have a bad remote(s)

Posted on Sep 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question?key program code for 06 xterra


1. Close and lock all doors with the driver's side power lock / unlock switch located
on drivers door panel.

2. Insert key into ignition and remove it from the ignition key cylinder at least 6 times
within 10 seconds. Your hazard lamps will flash if you have performed this step
successfully. NOTE: Withdraw key completely from ignition cylinder each time. If
this procedure is performed to fast, system will not enter programming mode.

3. Insert key into ignition and turn to the ACC position.

4. Within 5 seconds, push ANY button oon the keyless remote. Your hazard lamps
will flash. NOTE: Do not press the button on the remote more than one time or the
programming will not be successful.

5. If there are any remaining remotes (including old ones), Unlock then Lock all doors
using switch on drivers door panel and within 5 seconds press ANY button on the next
remote. Your hazard lamps will flash. Repeat this step for each remote (including any
existing remotes).

6. Turn key to the off position, remove key from the ignition. Unlock door using switch on
door panel and open drivers door.

7. Test remote(s).

Jun 27, 2016 | Cars & Trucks

1 Answer

Can't open hatch and my key won't unlock the doors. how do i open the tank?


Order a new keyfob from the dealer and have them program it to your car.

Jun 24, 2012 | 1999 Audi A4

1 Answer

How do you program new spare key for 2007 rodeo RA?


if its the ignition key it must be done by a dealer and have a lage black plastic head which has got a transponder in it. If you got a blank key cut at the locksmith it will turn the locks but wont start the car. Usually you get the dealer to do both supply ignition key and then get it cut, then they can program it.

but if your asking how to program the keyless entry remote follow this procedure.
take note step 5 is different for different year models.


Make sure that all the doors are closed and unlocked and wait for dome light to go out before starting.


Insert the ignition key into the ignition switch


Open drivers door


3 on/lock


Close/open drivers door


Wait 8 secs


On/lock/on (MY06-07) OR 2 on/lock OR on/lock (MY08)


Close drivers door


Hazards flash


Press remote & keep pressing one button & then the other slowly(2 secs) until locks start working(they wont operate if key is in ignition).


Hazards flash

Feb 23, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Program remote


The horn chirp can be disable by pressing the lock and unlock buttons simultaneously until the hazard lights flash, and no enable press the lock and unlock until the horn chirp.
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.
1. Close all doors and lock all doors
2. Insert and remove the key from the ignition key cylinder more than six times within 10 seconds. (The hazard warning lamp will then flash.) NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
3. Insert key on ignition key cylinder and turn ignition key switch to "AAC" position At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Press any button on the new remote controller once. (The hazard warning lamp will then flash)
NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed and programming is successful.
If there is only one remote controller skip step 5.
5. Additional ID code entry Release the door lock, then lock again with door lock/unlock switch (In power window main switch)
6. Remove key from ignition
7. Unlock driver side door, open driver side door and then close the door. (END)

Feb 20, 2010 | 2001 Nissan Pathfinder

2 Answers

How do I disable the alarm system on a 1998 VW beetle? I cannot start the car.


Get it bypassed ask for a good auto electrition.He will sort that out for you.hope that was usefull

Aug 01, 2009 | 1998 Volkswagen Beetle

3 Answers

2002 Nissan Altima windows roll down by themselves w/no key in


You need a body control computer, which controls the windows, door locks and other items. The new computer will have to be programed by a good imports shop or Nissan dealer.

Apr 12, 2009 | 2002 Nissan Altima

1 Answer

Remote locks the doors but will not unlock doors or trunk Battery


It is entirely possible that the unlock button on the remote is worn such that it is not making contact. I've seen this happen many times, as the unlock button is pressed so much more than lock. You might try to reprogram the remote first before you look into getting a new remote. The procedure goes like this. Close and lock all doors Key in and out of the ignition 6 times, hazard lights should flash twice Turn key into accessory or on position Unlock and lock doors with drivers switch Press lock or unlock on remote Hazards should flash again to verify recognition turn key off  manually unlock door and then open and shut it.  you should then be able to test remote. 
The key to the procedure is doing step two quickly Hope this helps, if not you may need another remote or see dealer.

Apr 11, 2009 | 2004 Infiniti I35

1 Answer

94 Camry Wagon ignition blocked, doors self-lock, flashers on


you may have had a bad connection at the battery that would cause this kind of problem

Dec 14, 2008 | 1994 Toyota Camry

1 Answer

Need to program remote keyless entry for 2003 nissan pulsar?


If it is a 2003 model year vehicle follow this procedure. If it doesn't work, you may have the wrong fob which happens all the time.

Sit in vehicle and close all doors.
COMPLETELY insert and remove ignition key more than six times within 10 seconds.
Hazard lights should flash twice.
Turn ignition to ACC position
Press and hold any button on the new key fob hazard lights will flash twice
For a second key fob using the master lock switch, lock and unlock the doors then hold down any button on the second remote until the hazard lamps flash twice.
Then you are done open the door to exit the programming mode.
If the lamps didn't flash when holding down the key fob make sure you have the right key fob, they are different for each car.

Nov 25, 2008 | 1990 Nissan Pulsar

2 Answers

Nissan Murano 2005 SL keyless entry remote programing, got a used remote, how can I program it?


Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Aug 06, 2008 | 2005 Nissan Murano

Not finding what you are looking for?
2003 Nissan Altima Logo

Related Topics:

485 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...