Question about 2004 Chevrolet Corvette

1 Answer

2004 corvette i need to install front license plate on a 04 vette

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

So you don't drill into the front fascia you can purchase an aftermarket bracket for just this problem. it installs in minutes and doesn't damage the front fascia. you can go to Napa,Oreillys etc. the cost is minimal. please rate this........thanks

Posted on Sep 01, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

04 Dodge Stratus license plate bulb

get printout/bulb from parts store..

Dec 26, 2013 | 2004 Dodge Stratus

1 Answer

License plate light out on my `04 gmc envoy,how do i replace it?

Has 2 screws for the cover, take them out and replace the bulb/s. Might check the seal that seals the entire license plate panel, it's black. Common problem is that this seal comes folded under from the factory and allows water into the bulb area.

Nov 29, 2010 | 2004 GMC Envoy

1 Answer

How do I replace a license plate bulb on 04 cadillac srx

Replacing the license plate bulbs was simple. It took all of 20 minutes. Don't let the directions fool you. Remove the lift gate screw.Use a 10mm deep socket to remove the 5 nuts.(you can see the nuts on long bolts).Get a screw driver and gently pry the panel up. You can see everything right in front of you. Easy job if you have ANY kind of common sense.

Nov 05, 2010 | 2004 Cadillac Deville

1 Answer

2004 vette, I have an engine analyzer module,

It should be right near the steering column under the dash. They are usually easily accessible -- I've never known GM to hide them. It may be behind a trim panel.

Apr 26, 2010 | 2004 Chevrolet Corvette

1 Answer

Taillight lense removal on 84 vette

If I remember you need to remove them from laying on the ground and going in from under the car behind the bumper. Some models did have 2 screws on the front the older ones had to be removed from behind the bumper.

May 24, 2009 | 1984 Chevrolet Corvette

1 Answer

How do i change rear turn signal bulb on 89 corvette, notmine???

Rear Turn Signal, Brake and Parking Lights 1984–89 VEHICLES
  1. If removing an inner bulb, remove the license plate. For outer bulb replacement, reach from under the vehicle.
  2. To remove the inner rear brake light, you must reach behind the license place and under the vehicle to access the bulb and socket
  3. Remove the socket from the lens by releasing the locking tab and twisting
  4. Once the bulb and socket are pulled from the rear of the lens, grasp it from behind the license plate opening
  5. Then, pull it out of the side and replace the bulb
  6. Remove the bulb from the socket and replace.
  7. Installation is the reverse of the removal procedure.

Apr 05, 2009 | 1989 Chevrolet Corvette

2 Answers

'04 honda crv bulb change

Its a 5 Watt light bulb. Just pull it out and take it to the store with you. Just remove the license plate to get to it.

Mar 16, 2009 | 2004 Honda CR-V

2 Answers

Replace turn signal bulbs on 2001 corvette

Rears are simply remove the two screws on the lens and remove the tail light from the Vette, twist the connector to get to the bulb. Reverse instructions to install. For the fronts jack up the front, remove the small closeout panel under each side, push the brake cooling duct to one side and twist the bulb socket out of the light to get to the bulb. Reverse instructions to install.

Feb 22, 2009 | 2001 Chevrolet Corvette

4 Answers

1977 chevy corvette wiring diagram

All the diagrams for your corvette can be found here:

Headlight wiring is towards the bottom of the page.

Hope this helps, have fun wrenching on that vette.

Jul 04, 2008 | 1977 Chevrolet Corvette

Not finding what you are looking for?
2004 Chevrolet Corvette Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides